Create Or Modify An Event; Special Tools And Accessories - Lightware HDMI-TPS-RX110AY Series User Manual


  
5.SoftwareControl-LightwareDeviceController
5.8.2. Create or Modify an Event
Wizard Mode
The wizard mode lists the most common conditions and actions, so the
userdoesnothavetolookforLW3nodesandproperties.
Step 1. Click on the Edit button of the desired Event; the Event editor is
displayed.
Step 2. The wizard mode is displayed as default. Select the desired
Categoryfirst(e.g.AudioorVideo).
Step 3. Select the desired Expression from the drop-down menu. If any
other parameter is necessary to set, it is going to be displayed.
Step 4. Press the Apply button to store the settings of the Condition.
Advanced Mode
The goal of this mode is the same as of the wizard: set the properties and methods for conditions and
actions. The difference is the number of the available and usable properties and methods of the LW3
protocol. Advanced mode allows almost all of it.
Step 1. Click on the Edit button of the desired Event; the
Event editor is displayed.
Step 2. The wizard mode is the default, press the
Advanced button. The LW3 protocol tree is
displayed showing the list of the properties in the
drop-down menu. Navigate to the desired node.
Step 3. Select the desired Property from the menu. The
manual of the property is displayed below to help
to select the necessary property and to set the
value.
Step 4. Set the desired value and operator, then press the
Apply button to store settings.
The Link Tool
The new interface allows creating more actions to the same condition. In that case, a condition can trigger
moreactions.TosetsuchanEvent,theLinktoolhasbeenintroduced.
Step 1. Click on the Edit button of the desired Event; the
Event editor is displayed.
Step 2. The wizard mode is displayed as default, press the
Link button.
Step 3. All the saved Events are analyzed and the conditions
are listed (it takes some seconds to finish). The
Show advanced expressions option allows showing
the exact path and set the value of the given property.
Step 4. Select the desired Condition and press the Apply button to store the settings.
HDMI-TPS-RX110AYseries–User'sManual
5.8.3. Special Tools and Accessories
The Name of the Event
The name of a port can be changed by typing the new name and clicking the Set button. The following
charactersareallowedwhennaming:
Letters(A-Z)and(a-z),numbers(0-9),specialcharacters:hyphen(-),underscore(_),andspace().
Enable or Disable an Event
The set Event can be enabled or disabled in the Event list, or directly in the Event editor window by setting
the tick mark beside the name.
Testing the Condition
WhenthedesiredConditionisarranged,thesettingcanbetested.TheEventlistandtheEventeditorcontains
a small panel that shows if the set condition is detected and how many times. The Counter can be reset by
the button in Event editor. If the Condition is true, the detected mark turns green for two seconds and the
Counter is increased.
Testing the Action
The method is the same as testing the Condition, but in this case, the Action can be triggered manually by
pressing the Test button.

TIPSANDTRICKS:
check the Actions without opening the Event editor.
Delay the Action
In most cases the Action is performed immediately after the Condition is detected. But sometimes a delay
is necessary between the Condition and the Action. Therefore, the new Event manager contains the Delay
panelwhichallowsthatfeaturewithbelowsettings:
▪
▪
▪
▪
TIPSANDTRICKS:

of a property but just the expression is displayed. The option is available in the Event list window or when
Linktoolisused.
Appliedfirmwarepackage:v1.4.0 | LDCsoftware:v2.4.0b3
The Test button is also placed on the Action panel in the Event list. Thus, you can
No delay:whentheCondition
no delay Condition = true
is detected, the Action is
launched.
simple delay Condition = true
delay: when the
Simple
Condition is detected, the still exist Condition = true
Action is launched after the
continously Condition = true
set time interval.
exist
when the
Still exists:
Condition is detected, the
Action is launched after the set time interval only if the Condition still exists.
Continuously exists:whentheConditionisdetected,theActionislaunchedafterthesettimeinterval
only if the Condition has been existing continuously.
Show advanced expressions option is a useful tool when you look for the path or value
Perform the action
Delay Perform the action
Delay Condition = true Perform the action
Perform the action
Delay
Time
44