Advertisement
bizhub C4000i/C3300i
Authentication device
KM USB Reader v2 HID iCLASS
Note *1
▪ A combination of the loadable driver and the IC card information setting file will be supplied as a loadable driver by KM.
Note *2
▪ If cards of HID iClass of OMNIKEY 5427CK (AU-205H) that require detailed settings are to be used, make the detailed settings
by using either one of the following methods:
▪ Using the Auth Device Tool Advanced for 5427CK (AU-205H), prepare a combination of the loadable driver and the IC card
information setting file and export it as a loadable driver.
▪ Using the Auth Device Tool Advanced for 5427CK (AU-205H), prepare the IC card information setting file only and install
the loadable driver in the MFP. Then, using the Data Administrator, write the IC card information setting file in the MFP.
▪ Reference "IC card information setting procedures"
Note *3
▪ If a YSoft card reader is used, all types of card will be reported as HID Prox card to the authentication program.
▪ To report the card type other than HID Prox to the authentication program, choose the corresponding card type shown in the
following list.
Card Reader Name
KM USB Reader v2
MultiReader HF
KM USB Reader v2 Legic
Advant
KM USB Reader v2 ASK FSK
125kHz
KM USB Reader v2 Mot/Ind
W26
KM USB Reader v2 HID Prox HID Prox
KM USB Reader v2 HID
iCLASS
• *3-1 The content (ID) to be read from the type A card setting differs from which to be read by using AU-201S.
• *3-2 When add the YSoft card reader to the authentication network composed of the present AU-201S, the ID may vary
depending on the card reader. Therefore, it is required to set the card type to TypeA (1), HID Prox (1) or HID iCLASS (1) and
register the card again.
• *3-3 For the content to be read from the HID Prox card, since the ID length is fixed to 16 bytes, the unused part will be bridged
with 0xFF.
• *3-4 If a card type other than HID Prox is selected, the card ID type will be set to up to 512 bytes, the card ID length will be
reported together with the card ID.
• *3-5 If the card type is set to HID Prox by using the LDAP-IC card authentication, specify the card ID type to be sent to the LDAP
server as shown below.
1. Software switch No.135 Hex: 00 Reports that the 1st byte shows the ID length of the card, the 2nd byte and after shows the
card ID. (Default)
2. Software switch No.135 Hex: 01 Reports the card ID with the ID length including the 1st byte.
Note *4
▪ To use FeliCa, make either of the following settings.
▪ Select [FeliCa] at [Administrator] -> [User Auth/Account Track] -> [Authentication Device Settings] -> [Card Authentication]
-> [IC Card type].
▪ Although [Use Card Reader Settings] is also selectable at [Administrator] -> [User Auth/Account Track] -> [Authentication
Device Settings] -> [Card] -> [IC Card type], "FeliCa" is dedicated for the card reader (OMNIKEY5427CK) settings.
▪ Make card reader (OMNIKEY5427CK) settings with the tool that is exclusively used for PC settings and downloaded from
the HID web page.
1.5 Coverage Rate Clear
To clear the coverage rate.
Setting value
Set
Unset
1.6 License Management
1.6.1 Activation
• To activate i-Option functions.
• The functions can be activated by selecting the desired function and enter the appropriate license code and function code.
• Administrators also can carry out the procedure No.14 or later step to activate i-Option functions through Administrator Settings.
NOTE
▪ You need to access License Management System (LMS) to implement each function setting.
▪ Before accessing the LMS, CE are required to register the E-mail address and the password in the LMS. To register, click [CE
Initial Registration] that is located in the upper right of CE Login screen.
<Procedure>
1. Prepare "token certification."
Loadable driver name (KM standard setting)
Readable Card Type
Mifare
LEGIC
EM4100, EM4102, RFID
125kHz
Indala
HID iCLASS
Select [Set] and [END] key will clear the coverage rate.
Not cleared
J BILLING SETTING/ENHANCED SECURITY/DEBUG SETTINGS > 1. BILLING
Card type to be reported to the
authentication program (Default)
(*3-3,*3-5)
HID Prox
HID Prox
HID Prox
HID Prox
HID Prox
HID Prox
Contents
J-4
Compatible IC cards
HID iCLASS
IC Card Information Setting (card type
to be reported) (*3-4)
TypeA (1) (*3-1,*3-2)
TypeA (1) (*3-1,*3-2)
EM4100/
EM4102/
RFID 125kHz
Indala
HID Prox (1) (*3-2)
HID iCLASS (1) (*3-2)
Default setting
SETTING
○
Advertisement
