Advertisement
bizhub C4000i/C3300i
JAM type
Misfeed at vertical transport
Paper jam of a sheet of paper left at the vertical transport section results, if a
section (When PF-P20 or
sheet of paper is determined to exist at a position detected when the main
PF-P21 is installed)
power switch is turned ON, a door is opened and closed, or a misfeed or
malfunction is reset.
Misfeed at 2nd transfer
Paper jam of a sheet of paper left at the 2nd transfer section results, if the
section
registration sensor (PS9) is turned ON (blocked) when the main power switch
is turned ON, a door is opened and closed, or a misfeed or malfunction is
reset.
Paper jam of a sheet of paper left at the 2nd transfer section results, if the
fusing loop sensor (PS10) is turned ON (blocked) when the main power switch
is turned ON, a door is opened and closed, or a misfeed or malfunction is
reset.
Paper jam of a sheet of paper left at the 2nd transfer section results, if a sheet
of paper is determined to exist at a position detected when the main power
switch is turned ON, a door is opened and closed, or a misfeed or malfunction
is reset.
Misfeed at paper exit
Paper jam of a sheet of paper left at the paper exit section results, if the paper
section
exit sensor (PS13) is turned ON (unblocked) when the main power switch is
turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
Paper jam of a sheet of paper left at the paper exit section results, if a sheet of
paper is determined to exist at a position detected when the main power
switch is turned ON, a door is opened and closed, or a misfeed or malfunction
is reset.
Misfeed at duplex pre-
Paper jam of a sheet of paper left at the duplex pre-registration section
registration section
results, if a sheet of paper is determined to exist at a position detected when
the main power switch is turned ON, a door is opened and closed, or a
misfeed or malfunction is reset.
Misfeed at duplex transport
Paper jam of a sheet of paper left at the duplex transport section results, if the
section
ADU transport sensor (PS11) is turned ON (unblocked) when the main power
switch is turned ON, a door is opened and closed, or a misfeed or malfunction
is reset.
Paper jam of a sheet of paper left at the duplex transport section results, if a
sheet of paper is determined to exist at a position detected when the main
power switch is turned ON, a door is opened and closed, or a misfeed or
malfunction is reset.
1.5 1#-##
1.5.1 10-01, 10-02, 10-40
Contents
JAM type
Misfeed at manual bypass paper feed section
JAM code
10-01, 10-02, 10-40
JAM detection timing
Misfeed processing
Right door
location
Relevant parts
Procedure
Step
1
Initial check items
2
PS9 I/O check, sensor check
3
CL2 load check
• Check code: 20
• Multi code: 4
4
CL4 load check
JAM detection timing
10-01
The leading edge of the paper is not turned ON (blocked) the registration sensor (PS9) even after
the lapse of a given period of time after the manual bypass tray starts to feed paper.
10-02
For paper fed from the manual bypass tray, loop forming has not been complete before a sheet
enters the registration roller because the rise timing of load to perform registration is earlier than the
rise timing of load to form a loop.
10-40
For paper fed from the manual bypass tray, the image write start signal permit continues to be
disabled for a predetermined period of time after the timing of the image write start signal output.
-
Paper jam of a sheet of paper left at the manual bypass paper feed section results, if a sheet of
paper is determined to exist at a position detected when the main power switch is turned ON, a door
is opened and closed, or a misfeed or malfunction is reset.
• Main motor (M1)
• Bypass tray paper feed clutch (CL2)
• Registration clutch (CL4)
• Registration sensor (PS9)
• Base board (BASEB)
Action
Control signal
-
BASEB CN22EA-13 (ON)
BASEB CN23E-10 (ON)
BASEB CN22EA-3 (ON)
L-4
L TROUBLESHOOTING > 1. JAM CODE
Ref. page
L.1.6.1 20-02, 20-10, 20-11, 20-12,
20-21, 20-26
L.1.7.1 30-01, 30-03
L.1.7.2 32-05, 32-06, 32-31
L.1.8.1 92-01, 92-02, 92-03, 92-04
L.1.8.2 93-03
Location of electrical component
-
13-C
9-K
12-C
Advertisement
