Table of Contents
Advertisement
8.7
Self-diagnostic Functions
The self-diagnostic function of the AXR is explained
in Section 6.5.
The HART configuration tool can be used to run
self-diagnostics on a device and check for incorrect
data settings.
(1) Using DD
The Self test and Status commands are available
for self-diagnostics. When Self test is run, the
display unit shows an error code and alarm
message if the device detects any illegal parameter
settings or functional faults.
• Procedure to call up the Self test display
Device Setup → Diagnosis/Service → Test/Status →
Self test
If no error is detected, "Self test OK" is displayed on
the configuration tool.
If the specific diagnostic item is known for the
check, you can directly call up the item by using the
Status command.
The status is categorized from 1 to 7. For details,
read the table at the end of Section 8.9.
Show an example below to confirm the status of
Status group 1.
• Procedure to call up the Status display
Device Setup → Diagnosis/Service → Test/Status →
Status → Status group 1
If no error is detected, "Off" is displayed on the
configuration tool.
If there is an error, "On" is displayed on the
configuration tool, and a countermeasure for that
error is necessary.
Example of display: Span > 10 m/s
Span < 0.3 m/s
TTL > 10000 p/s
TTL < 0.0001 p/s
4-20 Lmt Err
(2) Using DTM
The Device Status commands are used for
self-diagnostics. When Device Status is run,
the display unit shows an error code and alarm
message if the device detects any illegal parameter
settings or functional faults.
• Procedure to call up the Device Status display
Device Status
<8. OPERATION VIA HART CONFIGURATION TOOL (HART 5)>
On
Off
Off
Off
Off
If no error is detected, "Status: Normal" is displayed
on the configuration tool.
If the specific diagnostic item is known for the
check, you can directly call up the item by using the
Diagnostic List in the Device Status display.
The Diagnostic List is categorized to Device Status,
Hardware Failure, Transducer Status, Diag Status,
and Configuration.
If no error is detected, color symbol which shows
Normal State is displayed on top of the error
message.
If color symbol which shows Error State is
displayed, there is an error and a countermeasure
for that error is necessary.
8.8 HART Specific Functions
8.8.1 Trim Analog Output
This function is used to adjust the analog output at 4
mA and 20 mA with the D/A trim or Scaled D/A trim.
(1) D/A trim
Connect a calibration digital ammeter, and then
enter the read value of the ammeter for each
output of AXR.
• Procedure to call up the D/A trim display
DD
Device Setup → Diagnosis/Service
→ Adjustment → D/A trim
DTM
Calibration → D/A trim
(2) Scaled D/A trim
The output is adjusted by using a voltmeter or
other types of meters with 0 to 100% scale.
Example using a voltmeter:
4 mA DC → 1 V
20 mA DC → 5 V
Connect this meter, and enter the read value of
the meter for each output of AXR.
• Procedure to call up the Scaled D/A trim
display
DD
Device Setup → Diagnosis/Service
→ Calibration
→ Analog output trim →Scaled D/A
trim
DTM
Calibration → Scaled D/A trim
(3) Clear D/A trim
When output is reset to the original value, clear
the D/A trim.
• Procedure to call up the Clear D/A trim display
DD
Device Setup → Diagnosis/Service
→ Adjustment → Clear D/A trim
DTM
Calibration → Clear D/A trim
8-4
IM 01E30D01-01EN
Advertisement
Table of Contents
