Table of Contents
Advertisement
Mono/Mono Parallel
141: P4EQ // P4EQ through 185: Mt.BPM Dly//Mt.BPM
Dly are parallel effects, with the left input going through one
effect, and the right going through the other. These provide
various combinations of 4-band EQ, Compressor, Limiter,
Exciter, Overdrive, Wah, Chorus/Flanger, Phaser, and
Multitap Delay, as described below.
4 band EQ
For a description of the on-screen EQ graphic, see "011:
Stereo Parametric 4EQ" on page 774.
PARAMETRIC EQ
Trim
Sets the input level.
Band1 Fc [Hz]
Sets the center frequency of Band 1.
Q
Sets the bandwidth of Band 1. See "Q" on page 774.
Gain [dB]
Sets the gain of Band 1.
Band2 Fc [Hz]
Sets the center frequency of Band 2.
Q
Sets the bandwidth of Band 2. See "Q" on page 774.
Gain [dB]
Sets the gain of Band 2.
Band3 Fc [Hz]
Sets the center frequency of Band 3.
Q
Sets the bandwidth of Band3. See "Q" on page 774.
Gain [dB]
Sets the gain of Band 3.
Band4 Fc [Hz]
Sets the center frequency of Band 4.
Q
Sets the bandwidth of Band 4. See "Q" on page 774.
Gain [dB]
Sets the gain of Band 4.
OUTPUT
Pan
Sets the stereo image.
Wet/Dry
Sets the balance between the effect and the dry input.
Source
Selects a modulation source for Wet/Dry.
876
[0...100]
[20...1.00k]
[0.5...10.0]
[–18.0...+18.0]
[50...5.00k]
[0.5...10.0]
[–18.0...+18.0]
[300...10.00k]
[0.5...10.0]
[–18.0...+18.0]
[500...20.00k]
[0.5...10.0]
[–18.0...+18.0]
[L000...C064...R127]
[Dry, 1:99...99:1, Wet]
[Off...Tempo]
Amount
Sets the modulation amount for Wet/Dry.
Compressor
For details on the Compressor graphics, see "001: Stereo
Dyna Compressor" on page 761.
Pre EQ
Trim
Sets the EQ input level.
LEQ Gain [dB]
Sets the gain of the Low EQ.
HEQ Gain [dB]
Sets the gain of the High EQ.
COMPRESSOR
Sensitivity
Sets the sensitivity. See "Sensitivity" on page 761.
Attack
Sets the attack level. See "Attack" on page 762.
Output Level
Sets the output level.
OUTPUT
Pan
Sets the stereo image.
Wet/Dry
Sets the balance between the effect and the dry input.
Source
Selects a modulation source for Wet/Dry.
Amount
Sets the modulation amount for Wet/Dry.
Limiter
For details on the Limiter graphics, see "005: Stereo
Limiter" on page 768.
LIMITER
Ratio
Sets the signal compression ratio. See "Ratio" on page 763.
Threshold [dB]
Sets the level above which the compressor is applied. See
"Threshold [dB]" on page 763.
Attack
Sets the attack time. See "Attack [msec]" on page 764.
Release
Sets the release time. See "Release [msec]" on page 764.
[+/–100]
[0...100]
[–15...+15]
[–15...+15]
[1...100]
[1...100]
[0...100]
[L000...C064...R127]
[Dry, 1:99...99:1, Wet]
[Off...Tempo]
[+/–100]
[1.0:1...50.0:1, Inf:1]
[–40...0]
[1...100]
[1...100]
Advertisement
Table of Contents
