Table of Contents
Advertisement
4. Select either All or Assignments Only to specify the
Tone Adjust parameters you want to copy.
All: Copies all of the Tone Adjust parameters and their
values assigned to the switches and sliders.
Assignments Only: Copies only the parameters assigned
to the switches and sliders. Values will not be copied.
5. Press the OK button to execute the Copy Tone Adjust
command, or press the Cancel button if you decide to
cancel.
Reset Tone Adjust
Reset Tone Adjust is available when CONTROL ASSIGN
is set to Tone Adjust.
This command changes the Tone Adjust assignments, either
resetting them to default values or turning them all off.
1. Select "Reset Tone Adjust" to open the dialog box.
2. Use the "To" field to specify how the Tone Adjust
assignments will be reset.
All Off: All assignments are turned off.
Default Setting: The assignments will be reset to their
default settings for each program type (such as HD-1,
AL-1, CX-3). For more information, see "HD-1: Tone
Adjust" on page 111.
3. To execute the Reset Tone Adjust command, press the
OK button. To exit without resetting the assignments,
press the Cancel button.
Copy Oscillator
Copy Oscillator is available on all of the tabs under the
Basic/X-Y, OSC/Pitch, Filter, Amp/EQ, and AMS
Mix/Common Key Track pages.
This command is used to copy the settings from one
oscillator to another.
1. Select "Copy Oscillator" to open the dialog box.
2. Use the "From" field to select the oscillator that you
want to copy.
3. Use "Program" to select the bank and number of the
copy-source program. You can press a BANK
SELECT button to select the desired bank.
Note: If you're editing an HD-1 Program, you can't select
EXi Programs, and vice-versa.
4. If you check "Tone Adjust too," the Tone Adjust
settings will temporarily be turned off, and from the
copy-source Tone Adjust settings, the Common
PROGRAM: Page Menu Commands Reset Tone Adjust
portion and the assignments and current values of the
corresponding OSC portion will be copied.
If "Tone Adjust too" is unchecked, the Tone Adjust
settings will be maintained.
5. In "To," specify the copy destination oscillator.
6. To execute the Copy Oscillator command, press the
OK button. To cancel, press the Cancel button.
Swap Oscillator
Swap Oscillator is available on all of the tabs under the
Basic/X-Y, OSC/Pitch, Filter, Amp/EQ, and AMS
Mix/Common Key Track pages.
This command exchanges the settings of oscillators 1 and 2.
1. Select "Swap Oscillator" to open the dialog box.
2. To execute the Swap Oscillator command, press the
OK button. To cancel, press the Cancel button.
This can be selected only if Oscillator Mode (1–1a) is
Double.
Copy X-Y Envelope
Copy X-Y Envelope is available on the X-Y Envelope tab
of the Basic/X-Y/Controllers page.
This command copies X-Y envelope settings from the
specified program, combination/timbre, or song.
1. Select "Copy X-Y Envelope" to open the dialog box.
2. Use the "From" field to select the mode, bank, and
number of the desired copy-source.
This command copies the parameters of the X-Y
Envelope page of the corresponding mode.
Note: In order to replicate the way in which the relative
volume of oscillators is controlled by the X-Y and X-Y
envelope of the program selected for a combination
timbre or a MIDI song track, turn on the Enable Volume
Control check box in the X-Y Control page. To replicate
the CC control effects, turn on the Enable CC Control
check box in the X-Y CC page.
Use this command when you want to copy the Position or
Time/Tempo of a X-Y envelope in order to create an
envelope that produces the same movement.
3. Press the OK button to execute the command, or press
the Cancel button to cancel.
119
Advertisement
Table of Contents
