Table of Contents
Advertisement
PROGRAM mode: HD-1
(Program Select)
This selects the Split Program to add to the Main Program.
You can use all of the normal Program selection methods,
including bank and number, category, and Find.
Category image
This display-only graphic represents the category or sub-
category of the Split Program.
Octave
This adjusts the pitch of the Split Program in 1-octave units.
Internally, the Octave setting controls the Timbre's
Transpose parameter.
Volume
This adjusts the volume of the Split Program. The default
setting is 127.
Solo
This turns the Solo function on/off. If Solo is enabled, only
tracks with Solo On will sound; other tracks will be muted.
The setting will alternate on/off each time you press the Solo
button.
MAIN PROG
(Program Select)
By default, this will be the currently selected Program. You
can also select a different Program, if desired. You can use
all of the normal Program selection methods, including bank
and number, category, and Find.
Category image
This display-only graphic represents the category or sub-
category of the Main Program.
Octave
This sets the pitch of the Main Program in 1-octave units.
Internally, this edits all of the individual Timbre Transpose
parameters.
Solo
This turns the Solo function on/off. If Solo is enabled, only
tracks with Solo On will sound; other tracks will be muted.
The setting will alternate on/off each time you press the Solo
button.
Volume
This adjusts the volume of the Main Program. The default
setting is 127.
ARP/DRUM
Select ARP/DRUM
You can choose to use the ARP/DRUM from either the Main
or Split Program. The Tempo is initially set to match the
selected ARP/DRUM; you can then change it as desired.
When the ARP and DRUM buttons are turned on, notes can
be played using the arpeggiator, drum track or step
sequencer.
Note that you can't use both Arpeggiator, Drum track/Step
sequencer simultaneously.
12
[List of Programs]
[-2, -1, 0, +1, +2]
[000...127]
[On, Off]
[List of Programs]
[-2, -1, 0, +1, +2]
[On, Off]
[000...127]
Volume
This adjusts the volume of the Drum Track. Initially, the
value defaults to match the Drum Track volume in the source
Program.
Tempo
This sets the tempo for Arpeggiator, Drum track or Step
sequencer.
By default, this will be the tempo of the Program whose
ARP/DRUM is selected; you can then change it as desired.
Write Layered Combi
When you've created a layer sound that you like, press the
Write Layered Combi button to save it as a combination.
The Write Combination dialog box will appear. For more
information, see "Write Combination" on page 433.
After the Write is complete, the system enters
COMBINATION mode with the newly created Combination
selected.
Cancel
If you press the Cancel button the Quick Layer dialog box
closes, and the settings are canceled.
Settings that are saved in a Combination
The settings stored in the Combination are almost the same
as for Quick Layer; for more details, please see "Settings
that are saved in a Combination" on page 10. Quick Split
also controls the Key Zones, MIDI Filter and ARP settings,
as below:
Key Zone
When using Quick Split, this is set according to the Split
Mode and Split Point.
Also, the ARP Scan Zone will be set to match the Timbre
Key Zone. Timbre Zone Bypass will turn on.
MIDI Filter
When using Quick Split, MIDI Filter - Enable Damper is
turned on for the Main program Timbre (T01), and turned off
for the Lower(Upper) program Timbre (T02). This is
convenient for a typical piano/bass split, for instance.
v 0–1: Page Menu Commands
• Compare →p.112
• Write Program →p.112
• Exclusive Solo →p.113
• Show MS/WS/DKit Graphics →p.113
• Add To Set List →p.113
• Initialize Program →p.113
• Load required samples →p.114
• PAGE →p.126
• MODE →p.126
[000...127]
[040.00...300.00]
Advertisement
Table of Contents
