Table of Contents
Advertisement
PROGRAM mode: HD-1
PROGRAM: Page Menu Commands
Compare
Write Program
Exclusive Solo
Show MS/WS/DKit Graphics
Add To Set List
Initialize Program
Load required samples
Optimize RAM
Select Sample No.
Select Directory/File for Sample To Disk
Auto Sampling Setup
Copy Tone Adjust
Reset Tone Adjust
Copy Oscillator
Swap Oscillator
Copy X-Y Envelope
Sample Parameters
Sync Both EGs
Swap LFO 1&2
Copy External Scene
Copy Scene
Swap Scene
Initialize Scene
Copy Insert Effect
Swap Insert Effect
Insert IFX Slot
Cut IFX Slot
Clean Up IFX Routings
Copy MFX/TFX
Swap MFX/TFX
Write FX Preset
Remap MS/Sample Banks
PAGE
MODE
Compare
This command is available on all pages in PROGRAM
mode.
Use this when you wish to compare the edits you have made
to a Program or Combination's sound with the unedited
original (i.e., the sound that is saved in memory). When you
execute this command while editing a Program or
Combination, the last saved settings for that Program or
Combination number will be recalled. Use the Compare
command once more to return the settings to how they were
while you were editing them.
If the Compare command is not shown in the page menu
commands, you cannot revert to the edited version of the
settings.
Write Program
This command is available on every page in PROGRAM
mode.
This command writes an edited Program into the
NAUTILUS internal memory. It is available on every page
in PROGRAM mode.
Write Program lets you:
112
→p.112
• Save your edits
→p.112
• Rename the Program
→p.113
• Assign the Program to a Category
→p.113
• Mark the Program as a Favorite
→p.113
→p.113
• Copy the Program to a different Bank and number
→p.114
Be sure to Write any Program that you wish to keep. An
→p.114
edited Program cannot be recovered if you do not write it
→p.115
before turning off the power or selecting another
→p.115
Program.
→p.116
1. Select "Write Program" to open the dialog box.
→p.118
→p.119
→p.119
→p.119
→p.119
→p.120
→p.121
→p.121
→p.121
→p.121
The upper line of the dialog shows the Bank, number, and
→p.122
Program name.
→p.122
2. If you wish to modify the Program name, press the
→p.122
text edit button to move to the text edit dialog box,
→p.122
and enter the desired program name.
→p.122
If a USB QWERTY keyboard (commercially available) is
→p.123
connected, you can use this to enter text instead of the on-
→p.124
screen keyboard. For more information, see "Editing names
→p.125
and entering text" on page 202 of the OG.
→p.125
3. In Category and Sub Category, specify the category of
→p.125
the program that you are writing.
→p.125
The category can be used to find this Program when
→p.126
selecting a program in PROGRAM, COMBINATION, or
→p.126
SEQUENCER modes.
Note: You can edit these category names in the GLOBAL
Program Category page. For more information, see "3–1:
Program Category" on page 660.
4. Press "To Program" to specify the destination Bank
and number.
Important: HD-1 Programs can only be written to HD-1
Banks, and EXi Programs can only be written to EXi
Banks. For more information on the default Bank types,
and on how to change them, please see "Program Bank
Contents" on page 7, and "Changing the Program Bank
Types" on page 3.
5. To Write the Program, press the OK button. To
cancel, press the Cancel button.
Do not turn off the power for at least 10 seconds after
using the Write Program command. This allows the
system time to complete the process, which includes
saving a backup of the data to the internal drive.
Saving edits to GM Programs
You can edit GM Programs, but you must then save them to
a Bank other than INT-G; the GM Programs themselves
cannot be over-written.
Advertisement
Table of Contents
