Table of Contents
Advertisement
Release
Sets the release time. For more information, see "Release
[msec]" on page 764.
Gain Adjust [dB]
Sets the limiter output gain. For more information, see "Gain
Adjust [dB]" on page 764.
Pre EQ
Trim
Sets the EQ input level.
Pre LEQ Gain [dB]
Sets the gain of the Low EQ.
Pre HEQ Gain [dB]
Sets the gain of the High EQ
OD/HI-GAIN
DRIVE
For more information on these parameters, see "DRIVE" on
page 790.
Drive Mode
Switches between overdrive and high-gain distortion.
Drive
Sets the degree of distortion.
Output Level
Sets the overdrive output level.
Source
Selects the modulation source for the overdrive output level.
Amount
Sets the modulation amount of the overdrive output level.
EQ
Low Fc [Hz]
Sets the center frequency for low-frequency shelving EQ.
Gain [dB]
Sets the gain of the Low EQ.
Mid1 Fc [Hz]
Sets the center frequency for Mid/High EQ 1 (peaking type).
Q
Sets the band width of Mid/High EQ 1. For more
information, see "Q" on page 774.
Gain [dB]
Sets the gain of Mid/High EQ 1.
Mid2 Fc [Hz]
Sets the center frequency for Mid/High EQ 2 (peaking type).
Q
Sets the band width of Mid/High EQ 2. For more
information, see "Q" on page 774.
[1...100]
[–Inf, –38...+24]
[0...100]
[–15...+15]
[–15...+15]
[Overdrive, Hi-Gain]
[1...100]
[0...50]
[Off...Tempo]
[–50...+50]
[20...1.00k]
[–18...+18]
[300...10.00k]
[0.5...10.0]
[–18...+18]
[500...20.00k]
[0.5...10.0]
Mono-Mono Serial 108: Early Reflections Hi Dens
Gain [dB]
Sets the gain of Mid/High EQ 2.
WAH
CONTROL
Sweep Mode
Selects the control from auto-wah, modulation source, and
LFO. See "Sweep Mode" on page 778.
Source
Selects the modulation source for the wah when Sweep
Mode=Dmod.
LFO
Frequency [Hz]
Sets the LFO speed.
WAH
Frequency Bottom
Sets the lower limit of the wah center frequency. p.779.
Frequency Top
Sets the upper limit of the wah center frequency. p.779.
Resonance
Sets the resonance amount.
LPF
Switches the wah low pass filter on and off.
Wet/Dry
Sets the wah effect balance.
Source
Selects the Wet/Dry modulation source for the wah.
Amount
Sets the Wet/Dry modulation amount for the wah.
CHORUS/FLANGER
This effect can produce either chorusing or flanging,
depending on the settings.
The default settings create flanging.
To produce a chorus effect instead, change the settings as
follows:
• Frequency [Hz]: 0.80
• Delay Time [msec]: 20.0
• Depth: 70
• Feedback: +0
LFO
Waveform
Selects the LFO Waveform.
Frequency [Hz]
Sets the LFO speed.
[–18...+18]
[Auto, Dmod, LFO]
[Off...Tempo]
[0.02...20.00]
[0...100]
[0...100]
[0...100]
[Check-box]
[Dry, 1:99...99:1, Wet]
[Off...Tempo]
[+/–100]
[Triangle, Sine]
[0.02...20.00]
861
Advertisement
Table of Contents
