Table of Contents
Advertisement
MEDIA mode
If you enter SFX_*_00 or SFX_* and press OK, the
following files will be loaded:
SFX_A_00.WAV
SFX_A_01.WAV
SFX_B_00.WAV
SFX_B_01.WAV
SFX_C_00.WAV
Load .KSC
This loads all of the SAMPLING mode, EXs, and/or User
Sample Bank Multisamples, Samples, and Drum Samples
linked within the KSC.
For more information on User Sample Banks, see "User
Sample Banks" on page 149 of the OG.
If the KSC includes SAMPLING mode data, the
Multisamples and Samples (.KMP and .KSF files)
are saved in an automatically-created directory
with the same name as the .KSC file.
1. "KSC Allocation" allows you to specify how the
multisamples and samples in the .KSC file will be
loaded.
Append will leave all currently-loaded SAMPLING
mode, EXs, and User Sample Bank data intact.
SAMPLING mode Multisamples and Samples will be
loaded into the next available vacant numbers following
the existing data. (See the diagram ".KSC Allocation" on
page 704.)
If "Load ********.PCG too" is enabled, and the PCG's
Programs, Wave Sequences, and Drum Kits use the
KSC's SAMPLING mode data, the system will
automatically remap the Multisample and Sample
references so that everything plays correctly.
Clear Sampling mode Data will erase all Multisamples
and Samples from SAMPLING mode, and load the data
in the same configuration with which it was saved.
Existing EXs and User Sample Bank data is left intact.
Clear All is similar to Clear Sampling mode Data,
above, but also un-loads existing EXs and User Sample
Bank data before loading the new .KSC file. This frees up
the most memory for the new .KSC.
You can use the information at the bottom of the dialog
box, including Memory Required, (Memory) Available,
and Enough slots for Samples & MS, to determine
whether or not you need to free up room for the new
.KSC.
712
2. Set the Load Method as desired.
This sets the preferred way to load the KSC's EXs and
User Sample Bank data: load it into RAM, or use Virtual
Memory. Note that if the data is extremely large, and
would not fit into RAM even if no other samples were
loaded, the data will be loaded into Virtual Memory
regardless of this setting.
These settings apply only to EXs and User Sample Bank
data; SAMPLING mode data is always loaded into RAM.
RAM: The samples will be loaded into RAM. This has
the advantage of allowing reverse playback.
Virtual Memory: The samples will use Virtual Memory.
This generally allows you to load more large samples at
once. Note that the samples may still require a significant
amount of RAM.
KSC Settings: KSCs can store separate load method
settings for each Multisample or Drum Sample, based on
the settings when the KSC was saved. Setting Load
method to KSC Settings uses these individual settings.
3. If the current directory contains a .PCG file, and
.SNG file of the same filename, you can select the
"Load ********.PCG too" check box, and the "Load
********.SNG too" check box check box.
(See "Load: .PCG: 1")
• If you check "Load ********.PCG too," the .PCG file of
the same name as the .KSC file will also be loaded. (See
"Load .PCG: 2")
• If you check "Load ********.SNG too," the .SNG file
of the same name as the .KSC file will also be loaded.
(See "Load .PCG: 3")
4. To load the data, press the OK button. To cancel
without loading, press the Cancel button.
If the .KSF files used by the .KMP file are not in the
current directory or below it, a dialog box will appear,
allowing you to specify the directory. For more
information, see "If a file to be loaded cannot be found,
or when loading a file that was saved across media" on
page 702.
Since overflow checking of sample RAM is performed
when loading each individual .KSF file, it is possible that
an overflow may occur in the middle of the loading
process.
Loading individual files from within a .KSC file
Similar to .PCG files, you can browse inside a .KSC file as if
it were a folder on the disk. You can use this to load
individual Multisamples, Drum Samples, or Samples—
including more than one at a time, using Multiple Select.
Groups of data appear with folder icons within the .KSC. As
with folders on the disk, you can select one or more folders
to load all of their contents, or open a folder to browse
within.
The total size of all referenced files is shown to the right of
each item's name.
When you open a .KSC file, you'll see folders for each EXs
used by the .KSC. If the .KSC includes User Samples, there
will also be a folder titled User Sample Data. The folder and
file structure is as shown below.
User Sample Data folder
• Multisamples folder
Multisamples
Advertisement
Table of Contents
