MINOLTA-QMS Magicolor 2200 Series Manual page 154

5-Bin Mailbin B-11, C-36
Paper empty and paper full detection C-39
Paper exit modes C-36
Paper guide operation C-38
Paper path C-36
Switching arm operation C-37
5-bin mailbin
Adjustment D-29
Paper exit sensor adjustment E-34
Test mode E-33
A
Adjustment, 5-bin mailbin D-29
AIDC C-21
AIDC sensor C-17, C-22
Automatic Image Density Control (AIDC) C-21
B
Back-side printing paper C-33
Belt cleaner motor (M12 C-23
Belt cleaner pressure error E-27
Belt cleaner pressure error detection E-27
Belt cleaner section disassembly D-20
Black image troubleshooting E-36
Black spots troubleshooting E-36
Black/white lines and bands troubleshooting E-37
Blank image troubleshooting E-36
C
Cassette paper take-up section disassembly D-14
Circuit board layout B-23
Cleaner release position sensor disassembly D-21
Cleaning
General D-4
Laser lens cover D-4
Paper take-up roller D-4
Cleaning Blade C-8
Cleaning roller C-27
Color developing process C-11
Comb electrode C-8
Component layout B-14
Connector layout B-22
Control panel B-8
Counter control E-13
Cyclical (evenly spaced) image defect troubleshooting
E-38
D
Detection methods
Fusing unit E-14
Image transfer belt unit E-14
Image transfer roller unit E-14
Oil coating roller E-14
OPC drum E-14
Toner cartridge E-14
Waste toner container E-14
Developing C-15
Developing motor disassembly D-18
Developing motor removal caution D-6
Developing position of the toner cartridge C-13
Developing section C-11, C-13, C-14, C-15, C-16
Toner cartridges C-12
Developing section disassembly D-17
Dimensions B-3
Disassembly and Cleaning D-1
Disassembly procedures D-7
5-bin mailbin disassembly D-25
Belt cleaner section D-20
Cassette paper take-up section D-14
Developing section D-17
Duplex unit section D-22
Exterior covers D-7
Fan motors D-11
Fusing motor D-10
Fusing pressure motor D-11
Fusing section D-22
HV1 and HV2 D-10
Image transfer section D-19
Laser safety switch D-13
Laser unit section D-19
Multipurpose paper take-up tray D-14
Multipurpose tray take-up solenoid D-13
Paper exit section D-22
Power Supply (PU1) D-10
PWB-A D-10
Transport motor D-11
Transport section D-15
Waste toner full sensor D-13
Drive motor error codes E-22
Drive Transmission Gear C-5
Duplex paper take-up motor disassembly D-24
Duplex paper-detecting sensor disassembly D-22
Duplex unit C-33
Duplex printing method C-34
Duplex unit circuit board cover disassembly D-22
Duplex unit circuit board disassembly D-23
Duplex unit disassembly D-22
Duplex unit drive motor C-33
E
Electrical Components layout B-19
Electrode roller C-17
Engine test print E-5
Envelopes B-2
Erase (before image transfer) C-21
Eraser lamp C-17
Error code troubleshooting E-15
Error Codes
04 MAIN UNIT E-31
05 FLASH ROM E-31
08 MAIN MOTOR E-22
09 FUSING MOTOR E-23
0B XFER FAN BELT E-20
0C PWR SUPPLY FAN E-17
0D ENGINE FAN E-18
0E SUCTION FAN E-19
0F FUSING UNIT FAN E-21
10 POLYGON MOTOR E-25
12 LASER ERROR E-25
14 XFER ROLLER E-28
15 XFER BELT CLN E-27
16 XFER BELT ROT E-26
17 TONER RACK E-29
18 FUS UPP WARMUP E-16
19 FUS UPP LOWTMP E-16
1A FUS UPP HIG TMP E-16
1B FUS UPPER THERM E-16
1C FUS LOW WARMUP E-16
1D FUS LOW LOWTMP E-16
1E FUS LOW HIGTMP E-16
1F FUS LOW THERM E-16
20 FUS RETRACT E-24
21 TRANS DET SENSOR E-30
22 MAN TRAY LIFT E-30
I-2