Index - Siemens SINUMERIK 840D sl Function Manual

Index

$
$A_DP_IN_CONF, 63
$A_DP_IN_STATE, 63
$A_DP_IN_VALID, 63
$A_DP_OUT_CONF, 63
$A_DP_OUT_STATE, 63
$A_DP_OUT_VALID, 63
$A_IN, 34
$A_INA, 34
$A_INCO, 49
$A_OUT, 34, 36
$A_OUT[n], 603
$A_OUTA, 34, 44
$AA_ACT_INDEX_AX_POS_NO, 824
$AA_COUP_ACT, 771
$AA_COUP_OFFS, 771
$AA_ENC_COMP, 270
$AA_ENC_COMP_IS_MODULO, 270
$AA_ENC_COMP_MAX, 269
$AA_ENC_COMP_MIN, 269
$AA_ENC_COMP_STEP, 269
$AA_FIX_POINT_ACT, 190
$AA_FIX_POINT_SELECTED, 190
$AA_G0MODE, 662
$AA_ISTEST, 360
$AA_MOTEND, 678
$AA_PROG_INDEX_AX_POS_NO, 824
$AC_AXCTSWA, 115
$AC_AXCTSWE, 115
$AC_ISTEST, 360
$AC_RETPOINT, 740
$AN_AXCTAS, 115
$AN_AXCTSWA, 115
$AN_CEC, 277
$AN_CEC_DIRECTION, 278
$AN_CEC_INPUT_AXIS, 277
$AN_CEC_IS_MODULO, 278
$AN_CEC_MAX, 278
$AN_CEC_MIN, 277
$AN_CEC_MULT_BY_TABLE, 278
$AN_CEC_OUTPUT_AXIS, 277
$AN_CEC_STEP, 277
$AN_LAI_AX_IS_AXCTAX, 115
$AN_LAI_AX_IS_LEADLINKAX, 115
$AN_LAI_AX_IS_LINKAX, 115
$AN_LAI_AX_TO_IPO_NC_CHANAX, 115
$AN_LAI_AX_TO_MACHAX, 115
Extended Functions
Function Manual, 10/2015, 6FC5397-1BP40-5BA3
$AN_REBOOT_DELAY_TIME, 347
$P_COUP_OFFS, 772
$P_GWPS, 871
$P_ISTEST, 360
$TC_DP1, 846
$TC_DPC1...10, 846
$TC_TPC1...10, 851
$TC_TPG3, 850
$TC_TPG4, 850
$TC_TPG5, 850
$TC_TPG6, 850
$TC_TPG7, 850
$TC_TPG8, 850
$TC_TPG9, 851
$VA_COUP_OFFS, 771
1
1dimensional
Setpoint selection ($AC_MEAS_TYPE = 19), 547
2
2dimensional
Setpoint selection ($AC_MEAS_TYPE = 20), 548
3
3D Probe, 514
3dimensional
Setpoint selection ($AC_MEAS_TYPE = 21), 550
A
Acceleration characteristic, 624
Acknowledgement of manual stroke initiation, 931
Acknowledgement of stopped status, 934
Activating an axis replacement without a
preprocessing stop, 372
Activation methods, 758
Activation of coupling, 758
Active file system, 800
Active infeed axes, 938
Active/passive operating mode, 892
Active/passive operating mode of control unit, 893
Actual value coupling, 941
Actual value for analog NCK inputs, 885
977