Danfoss VLT FC 103 Programming Manual page 86

Parameter Description
13-01 Start Event
Option: Function:
[21] Alarm (trip lock) See parameter group 5-3* for further
description.
[22] Comparator 0 Use the result of comtor 0 in the logic
rule.
[23] Comparator 1 Use the result of comtor 1 in the logic
rule.
[24] Comparator 2 Use the result of comtor 2 in the logic
rule.
[25] Comparator 3 Use the result of comtor 3 in the logic
rule.
[26] Logic rule 0 Use the result of logic rule 0 in the
logic rule.
[27] Logic rule 1 Use the result of logic rule 1 in the
logic rule.
[28] Logic rule 2 Use the result of logic rule 2 in the
logic rule.
[29] Logic rule 3 Use the result of logic rule 3 in the
logic rule.
[33] Digital input DI18 Use the value of DI18 in the logic rule
(High = TRUE).
[34] Digital input DI19 Use the value of DI19 in the logic rule
(High = TRUE).
[35] Digital input DI27 Use the value of DI27 in the logic rule
(High = TRUE).
[36] Digital input DI29 Use the value of DI29 in the logic rule
(High = TRUE).
[37] Digital input DI32 Use the value of DI32 in the logic rule
(High = TRUE).
[38] Digital input DI33 Use the value of DI33 in the logic rule
(High = TRUE).
[39] Start command This event is TRUE if the frequency
converter is started by any means
(either via digital input, field bus or
other).
[40] Drive stopped This event is TRUE if the frequency
converter is stopped or coasted by any
means (either via digital input, fieldbus
or other).
[41] Reset Trip This event is TRUE if the frequency
converter is tripped (but not trip-
locked) and [Reset] is pressed.
[42] Auto Reset Trip This event is TRUE if the frequency
converter is tripped (but not trip-
locked) and an Automatic Reset is
issued.
[43] OK Key This event is TRUE if [OK] is pressed.
[44] Reset Key This event is TRUE if [Reset] is pressed.
®
VLT Refrigeration Drive Programming Guide
13-01 Start Event
Option:
[45] Left Key
[46] Right Key
[47] Up Key
[48] Down Key
[50] Comparator 4
[51] Comparator 5
[60] Logic rule 4
[61] Logic rule 5
13-02 Stop Event
Option:
[0]
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10] Out of speed range
[11] Below speed low
[12] Above speed high
[13] Out of feedb.
®
MG16H102 - VLT is a registered Danfoss trademark
Function:
This event is TRUE if [◄] is pressed.
This event is TRUE if [►] is pressed.
This event is TRUE if [
This event is TRUE if [
Use the result of comtor 4 in the logic
rule.
Use the result of comtor 5 in the logic
rule.
Use the result of logic rule 4 in the
logic rule.
Use the result of logic rule 5 in the
logic rule.
Function:
Select the boolean (TRUE or FALSE)
input to deactivate Smart Logic
Control.
False Enters the fixed value of FALSE in the
*
logic rule.
True Enters the fixed value TRUE in the
logic rule.
Running See parameter group 5-3* for further
description.
In range See parameter group 5-3* for further
description.
On reference See parameter group 5-3* for further
description.
Torque limit See parameter group 5-3* for further
description.
Current Limit See parameter group 5-3* for further
description.
Out of current See parameter group 5-3* for further
range description.
Below I low See parameter group 5-3* for further
description.
Above I high See parameter group 5-3* for further
description.
See parameter group 5-3* for further
description.
See parameter group 5-3* for further
description.
See parameter group 5-3* for further
range description.
3 3
▲
] is pressed.
▼
] is pressed.
85