Danfoss VLT FC 103 Programming Manual page 31

Parameter Description
0-20 Display Line 1.1 Small
Option:
[1661] Terminal 53 Switch
Setting
[1662] Analog Input 53
3 3
[1663] Terminal 54 Switch
Setting
[1664] Analog Input 54
[1665] Analog Output 42
[mA]
[1666] Digital Output [bin]
[1667] Pulse Input #29 [Hz] Actual value of the frequency
[1668] Pulse Input #33 [Hz] Actual value of the frequency
[1669] Pulse Output #27
[Hz]
[1670] Pulse Output #29
[Hz]
[1671] Relay Output [bin]
[1672] Counter A
[1673] Counter B
[1675] Analog In X30/11
[1676] Analog In X30/12
[1677] Analog Out X30/8
[mA]
[1680] Fieldbus CTW 1
[1682] Fieldbus REF 1
[1684] Comm. Option STW
30
®
VLT Refrigeration Drive Programming Guide
Function:
Setting of input terminal 53.
Current = 0; Voltage = 1.
Actual value at input 53 either as a
reference or protection value.
Setting of input terminal 54.
Current = 0; Voltage = 1.
Actual value at input 54 either as
reference or protection value.
Actual value at output 42 in mA.
Use 6-50 Terminal 42 Output to
select the variable to be
represented by output 42.
Binary value of all digital outputs.
applied at terminal 29 as a pulse
input.
applied at terminal 33 as a pulse
input.
Actual value of pulses applied to
terminal 27 in digital output mode.
Actual value of pulses applied to
terminal 29 in digital output mode.
View the setting of all relays.
View the present value of Counter
A.
View the present value of Counter
B.
Actual value of the signal on input
X30/11 (General Purpose I/O Card.
Option)
Actual value of the signal on input
X30/12 (General Purpose I/O Card.
Optional)
Actual value at output X30/8
(General Purpose I/O Card.
Optional) Use Par. 6-60 to select the
variable to be shown.
Control word (CTW) received from
the Bus Master.
Main reference value sent with
control word via the serial
communications network e.g. from
the BMS, PLC or other master
controller.
Extended fieldbus communication
option status word.
®
MG16H102 - VLT
0-20 Display Line 1.1 Small
Option:
[1685] FC Port CTW 1
[1686] FC Port REF 1
[1690] Alarm Word
[1691] Alarm Word 2
[1692] Warning Word
[1693] Warning Word 2
[1694] Ext. Status Word
[1695] Ext. Status Word 2
[1696] Maintenance Word
[1830] Analog Input X42/1
[1831] Analog Input X42/3
[1832] Analog Input X42/5
[1833] Analog Out X42/7
[V]
[1834] Analog Out X42/9
[V]
[1835] Analog Out X42/11
[V]
[2117] Ext. 1 Reference
[Unit]
[2118] Ext. 1 Feedback
[Unit]
[2119] Ext. 1 Output [%]
is a registered Danfoss trademark
Function:
Control word (CTW) received from
the Bus Master.
Status word (STW) sent to the Bus
Master.
One or more alarms in a Hex code
(used for serial communications)
One or more alarms in a Hex code
(used for serial communications)
One or more warnings in a Hex
code (used for serial communi-
cations)
One or more warnings in a Hex
code (used for serial communi-
cations)
One or more status conditions in a
Hex code (used for serial communi-
cations)
One or more status conditions in a
Hex code (used for serial communi-
cations)
The bits reflect the status for the
programmed Preventive
Maintenance Events in parameter
group 23-1*
Shows the value of the signal
applied to terminal X42/1 on the
Analog I/O card.
Shows the value of the signal
applied to terminal X42/3 on the
Analog I/O card.
Shows the value of the signal
applied to terminal X42/5 on the
Analog I/O card.
Shows the value of the signal
applied to terminal X42/7 on the
Analog I/O card.
Shows the value of the signal
applied to terminal X42/9 on the
Analog I/O card.
Shows the value of the signal
applied to terminal X42/11 on the
Analog I/O card.
The value of the reference for
extended Closed Loop Controller 1
The value of the feedback signal for
extended Closed Loop Controller 1
The value of the output from
extended Closed Loop Controller 1