Starting Up; Connecting; Switching On - Barco TransForm A User Manual

3.3 Starting up

3.3.1 Connecting

Mouse and keyboard must be connected to the respective connectors on the rear of the P
to sections 3.2.2 Mouse and
•
In an OmniBus configuration connect the link interface and remote power on/off cables to the T
devices. If an external genlock signal is used, connect it also to the P
and 3.2.13 CPU board!
•
In a Processor configuration, if necessary, connect the E
Extender!
Plug in the power cables on the back panel of the T
Connect the graphic cards to the O
cards or O S . At least one display must be connected for administrating T
MNI CALERS
Graphic cards and 3.2.6 OmniScaler! Connect the video and RGB sources to the input cards of T
refer to section 3.2.7 Quad Analog Video
Input Card!
Connect the P to the local area network by connecting the network to the network card or the network
ROCESSOR
onboard adapter! Please, refer to section

3.3.2 Switching on

•
In an OmniBus configuration:
Using O B A18 first make sure that the power switches [26]
MNI US
devices are on. The LED operating status [3]
Check also that the power switches [35]
on.
Using O B A12 just make sure that the red LED standby / component failed [6]
MNI US
nently on, indicating Standby mode.
Then switch on the P
remote power on/off mechanism all T
necessary order. The LED operating status of the O
on [4] on the OmniBus A12 should be lighting.
•
In a Processor configuration, switch on the P
front!
Initial system start after delivery
After the pre-configuration at the factory of a T
T F A at your site for the first time, the Windows 2000 or XP Professional Setup starts and prompts you
RANS ORM
to enter information to adjust the T
Then the Setup will prompt you to adjust the regional and language options and to personalize your software.
After that enter the product key.
The Microsoft Windows product key is labeled on the inside of the front flap of the
Processor.
When asked for the administrator password, enter barco and reenter it once again. Finally adjust the date and
time settings as well as the network settings. After entering the workgroup or computer domain, the system
reboots automatically and is from then on ready for normal operation.
Barco – TransForm A - Workstation for Windows – DOC-3266-2 – Revision 13 – April 2006
3.2.3 Keyboard!
S , if O
MNI CALERS
Card, 3.2.8 Streaming Video
3.2.12 Network!
(Figure
by pressing the power button [13]
ROCESSOR
F
RANS ORM
F A to your site. First read the license agreement before you accept it.
RANS ORM
ROCESSOR
to the P
XTENDERS
F A devices. Please, refer to section
RANS ORM
S are used. Connect the display devices to the graphic
MNI CALERS
Card, 3.2.9 Quad SDI Video Card
(Figure
(Figure 3-10) on each O
MNI
3-5) on the rear of the P
(Figure
A devices are now centrally switched on and initialized in the
B A18 should show a green light and the LED power
MNI US
by pressing the power button [13]
ROCESSOR
F A system it is sealed. Therefore when switching on
RANS ORM
_______________________________________________________________
3. Getting started
ROCESSOR
. Please refer to 3.2.14 OmniBus
. Please, refer to
ROCESSOR
3.2.1 Power
F A. Please, refer to
RANS ORM
F
RANS ORM
and 3.2.10 Dual RGB
3-11) of all connected O
MNI
B A18 should show a red light.
US
(if available) are switched
ROCESSOR
(Figure 3-7) is perma-
3-1) on its front! By means of the
(Figure
. Please, refer
F A
RANS ORM
3.2.15
supply!
3.2.5
A. Please,
B A18
US
3-1) on the
3-38