YOKOGAWA WT1800 User Manual page 44

5.1 List of Commands
Command
:MOTor:SPEed:TYPE
:MOTor:SPEed:UNIT
:MOTor:SSPeed
:MOTor:SYNChronize
:MOTor:TORQue?
:MOTor:TORQue:AUTO
:MOTor:TORQue:LSCale?
:MOTor:TORQue:LSCale:AVALue
:MOTor:TORQue:LSCale:BVALue
:MOTor:TORQue:LSCale:CALCulate? Queries all parameter calculation settings for the linear scale of the torque
:MOTor:TORQue:LSCale:CALCulate:
{P1X|P1Y|P2X|P2Y}
:MOTor:TORQue:LSCale:CALCulate:
EXECute
:MOTor:TORQue:PRANge
:MOTor:TORQue:RANGe
:MOTor:TORQue:RATE?
:MOTor:TORQue:RATE:{UPPer|LOW
er}
:MOTor:TORQue:SCALing
:MOTor:TORQue:TYPE
:MOTor:TORQue:UNIT
NUMeric Group
:NUMeric?
:NUMeric:FORMat
:NUMeric:HSPeed?
:NUMeric:HSPeed:CLEar
:NUMeric:HSPeed:DELete
:NUMeric:HSPeed:HEADer?
:NUMeric:HSPeed:ITEM<x>
:NUMeric:HSPeed:{MAXimum|MINim
um}?
:NUMeric:HSPeed:NUMber
:NUMeric:HSPeed:PRESet
:NUMeric:HSPeed:VALue?
:NUMeric:HOLD
:NUMeric:LIST?
:NUMeric:LIST:CLEar
:NUMeric:LIST:DELete
:NUMeric:LIST:ITEM<x>
:NUMeric:LIST:NUMber
:NUMeric:LIST:ORDer
:NUMeric:LIST:PRESet
5-12
Function
Sets or queries the revolution signal input type.
Sets or queries the unit that is added to the rotating speed computation
result.
Sets or queries the frequency measurement source for the synchronous
speed (SyncSp) computation.
Sets or queries the synchronization source for the rotating speed (Speed)
and torque (Torque) computations.
Queries all torque (Torque) settings.
Sets or queries the voltage auto range on/off status of the torque signal
(analog input type).
Queries all torque signal (analog input type) linear scaling settings.
Sets or queries the slope (A) of the linear scale of the torque signal (analog
input type).
Sets or queries the offset (B) of the linear scale of the torque signal (analog
input type).
signal (analog input type).
Sets or queries the data (Point1X, Point1Y, Point2X, or Point2Y) for
parameter calculations of the linear scale of the torque signal (analog input
type).
Calculates parameters for the linear scale of the torque signal (analog input
type).
Sets or queries the range of the torque signal (pulse input type).
Sets or queries the voltage range of the torque signal (analog input type).
Queries all torque signal (pulse input type) rated-value settings.
Sets or queries the upper or lower limit of the rated value of the torque signal
(pulse input type).
Sets or queries the torque computation scaling factor.
Sets or queries the torque signal input type.
Sets or queries the unit that is added to the torque computation result.
Queries all numeric data output settings.
Sets or queries the numeric data format.
Queries all numeric data output settings of the high speed data capturing
mode.
Clears high speed data capturing mode numeric list data output items (sets
the items to NONE).
Deletes high speed data capturing mode numeric list data output items.
Queries the header of the numeric data of high speed data capturing mode. 5-81
Sets or queries the output item (function and element) of the specified high
speed data capturing mode numeric data item.
Queries the maximum or minimum value of the numeric data of high speed
data capturing mode.
Sets or queries the number of numeric data items that are transmitted by the
:NUMeric:HSPeed:VALue? command.
Presets the numeric data output item pattern of the high speed data
capturing mode.
Queries the numeric data of high speed data capturing mode.
Sets or queries the on/off (hold/release) status of the numeric data hold
feature.
Queries all harmonic measurement numeric list data output settings.
Clears harmonic measurement numeric list data output items (sets the items
to NONE).
Deletes harmonic measurement numeric list data output items.
Sets or queries the output item (function and element) of the specified
harmonic measurement numeric list data item.
Sets or queries the number of numeric list data items that are transmitted by
:NUMeric:LIST:VALue?.
Sets or queries the maximum output harmonic order of the harmonic
measurement numeric list data.
Presets the harmonic measurement numeric list data output item pattern.
Page
5-77
5-77
5-77
5-77
5-77
5-78
5-78
5-78
5-78
5-78
5-78
5-78
5-78
5-78
5-79
5-79
5-79
5-79
5-79
5-80
5-80
5-80
5-80
5-80
5-81
5-81
5-81
5-82
5-82
5-83
5-83
5-83
5-83
5-84
5-84
5-84
5-84
IM WT1801-17EN