YOKOGAWA WT1800 User Manual page 108

5.16 MOTor Group
:MOTor:PM:SCALing
Function Sets or queries the motor output computation
scaling factor.
:MOTor:PM:SCALing {<NRf>}
Syntax
:MOTor:PM:SCALing?
<NRf> = 0.0001 to 99999.9999
:MOTOR:PM:SCALING 1
Example
:MOTOR:PM:SCALING? ->
:MOTOR:PM:SCALING 1.0000
:MOTor:PM:UNIT
Function Sets or queries the unit that is added to the motor
output computation result.
:MOTor:PM:UNIT {<String>}
Syntax
:MOTor:PM:UNIT?
<String> = Up to 8 characters
:MOTOR:PM:UNIT "W"
Example
:MOTOR:PM:UNIT? ->
:MOTOR:PM:UNIT "W"
Description This command has no effect on the computation
result.
:MOTor:POLE
Function Sets or queries the motor's number of poles.
:MOTor:POLE {<NRf>}
Syntax
:MOTor:POLE?
<NRf> = 1 to 99
:MOTOR:POLE 2
Example
:MOTOR:POLE? ->
:MOTOR:POLE 2
:MOTor:SPEed?
Function Queries all rotating speed (Speed) settings.
:MOTor:SPEed?
Syntax
:MOTor:SPEed:AUTO
Function Sets or queries the voltage auto range on/off
status of the revolution signal (analog input type).
:MOTor:SPEed:AUTO {<Boolean>}
Syntax
:MOTor:SPEed:AUTO?
:MOTOR:SPEED:AUTO ON
Example
:MOTOR:SPEED:AUTO? ->
:MOTOR:SPEED:AUTO 1
Description This command is valid when the revolution
signal input type (:MOTor:SPEed:TYPE) is set to
ANALog (analog input).
:MOTor:SPEed:LSCale?
Function Queries all revolution signal (analog input type)
linear scaling settings.
:MOTor:SPEed:LSCale?
Syntax
Description Linear scaling settings are valid when the
revolution signal input type (:MOTor:SPEed:
TYPE) is set to ANALog (analog input).
5-76
:MOTor:SPEed:LSCale:AVALue
Function Sets or queries the slope (A) of the linear scale of
the revolution signal (analog input type).
:MOTor:SPEed:LSCale:AVALue {<NRf>}
Syntax
:MOTor:SPEed:LSCale:AVALue?
<NRf> = 1.000E-03 to 1.000E+06
:MOTOR:SPEED:LSCALE:AVALUE 1.000
Example
:MOTOR:SPEED:LSCALE:AVALUE? ->
:MOTOR:SPEED:LSCALE:AVALUE 1.000E+00
:MOTor:SPEed:LSCale:BVALue
Function Sets or queries the offset (B) of the linear scale of
the revolution signal (analog input type).
:MOTor:SPEed:LSCale:BVALue {<NRf>}
Syntax
:MOTor:SPEed:LSCale:BVALue?
<NRf> = -1.000E+06 to 1.000E+06
:MOTOR:SPEED:LSCALE:BVALUE 0
Example
:MOTOR:SPEED:LSCALE:BVALUE? ->
:MOTOR:SPEED:LSCALE:BVALUE 0.000E+00
:MOTor:SPEed:LSCale:CALCulate?
Function Queries all parameter calculation settings for the
linear scale of the revolution signal (analog input
type).
:MOTor:SPEed:LSCale:CALCulate?
Syntax
:MOTor:SPEed:LSCale:CALCulate:
{P1X|P1Y|P2X|P2Y}
Function Sets or queries the data (Point1X, Point1Y,
Point2X, or Point2Y) for parameter calculations
of the linear scale of the revolution signal (analog
input type).
:MOTor:SPEed:LSCale:CALCulate:
Syntax
{P1X|P1Y|P2X|P2Y} {<NRf>}
:MOTor:SPEed:LSCale:CALCulate:
{P1X|P1Y|P2X|P2Y}?
<NRf> = -1.000E+12 to 1.000E+12
:MOTOR:SPEED:LSCALE:CALCULATE:P1X 0
Example
:MOTOR:SPEED:LSCALE:CALCULATE:
P1X? ->
:MOTOR:SPEED:LSCALE:CALCULATE:
P1X 0.000E+00
:MOTor:SPEed:LSCale:CALCulate:
EXECute
Function Calculates parameters for the linear scale of the
revolution signal (analog input type).
:MOTor:SPEed:LSCale:CALCulate:
Syntax
EXECute
:MOTOR:SPEED:LSCALE:CALCULATE:
Example
EXECUTE
Description The WT1800 uses the data that has been
specified (Point1X, Point1Y, Point2X, and
Point2Y) to calculate and set the slope (A) and
offset (B) of the linear scale.
IM WT1801-17EN