Siemens SINUMERIK 840D sl Operating Manual page 10

Table of contents
4.3.2 Current planes in cycles and input screens .............................................................................. 143
4.3.3 Hiding cycle parameters............................................................................................................ 144
4.3.4 Call and return conditions for cycles ......................................................................................... 144
4.3.5 Cycles for single position or position pattern (MCALL)............................................................. 144
4.3.6 Checking cycle parameters during the programming and the cycle execution ........................ 146
4.3.7 Setting data for cycles............................................................................................................... 147
4.3.8 Cycles that can be recompiled .................................................................................................. 149
4.3.9 Additional functions in the input screens................................................................................... 149
4.3.10 Blank input ................................................................................................................................ 150
4.4 Drilling ....................................................................................................................................... 151
4.4.1 General...................................................................................................................................... 151
4.4.2 Centering - CYCLE81 ............................................................................................................... 152
4.4.3 Drilling - CYCLE82 .................................................................................................................... 154
4.4.4 Reaming - CYCLE85................................................................................................................. 156
4.4.5 Deep-hole drilling - CYCLE83 ................................................................................................... 158
4.4.6 Boring - CYCLE86..................................................................................................................... 162
4.4.7 Tapping - CYCLE84, 840 .......................................................................................................... 165
4.4.8 Positioning and position patterns .............................................................................................. 170
4.4.8.1 General information................................................................................................................... 170
4.4.8.2 Arbitrary positions - CYCLE802 ................................................................................................ 170
4.4.8.3 Line position pattern - HOLES1 ................................................................................................ 172
4.4.8.4 Circle position pattern - HOLES2.............................................................................................. 175
4.5 Rotate........................................................................................................................................ 177
4.5.1 General...................................................................................................................................... 177
4.5.2 Stock removal - CYCLE951 ...................................................................................................... 177
4.5.3 Groove - CYCLE930 ................................................................................................................. 181
4.5.4 Undercut form E and F - CYCLE940 ........................................................................................ 185
4.5.5 Thread undercuts - CYCLE940................................................................................................. 188
4.5.6 Thread turning - CYCLE99........................................................................................................ 191
4.5.7 Thread chain - CYCLE98 .......................................................................................................... 200
4.5.8 Cut-off CYCLE92 ...................................................................................................................... 203
4.6 Contour turning ......................................................................................................................... 206
4.6.1 General information................................................................................................................... 206
4.6.2 Creating a new contour ............................................................................................................. 207
4.6.3 Creating contour elements ........................................................................................................ 208
4.6.4 Changing the contour................................................................................................................ 211
4.6.5 Contour call - CYCLE62............................................................................................................ 212
4.6.6 Stock removal ........................................................................................................................... 213
4.7 Milling ........................................................................................................................................ 216
4.7.1 Face milling - CYCLE61............................................................................................................ 216
4.7.2 Rectangular pocket - POCKET3 ............................................................................................... 219
4.7.3 Circular pocket - POCKET4 ...................................................................................................... 223
4.7.4 Rectangular spigot - CYCLE76................................................................................................. 228
4.7.5 Circular spigot - CYCLE77 ........................................................................................................ 231
4.7.6 Multi-edge - CYCLE79 .............................................................................................................. 234
4.7.7 Longitudinal groove - SLOT1 .................................................................................................... 237
4.7.8 Circumferential groove - SLOT2 ............................................................................................... 240
4.7.9 Elongated hole - LONGHOLE ................................................................................................... 244
4.7.10 Thread milling - CYCLE70 ........................................................................................................ 247
4.8 Contour milling .......................................................................................................................... 251
4.8.1 General information................................................................................................................... 251
4.8.2 Representation of the contour................................................................................................... 251
4.8.3 Creating a new contour ............................................................................................................. 253
10
Operating Manual, 01/2008, 6FC5398-7AP10-0BA0
HMI sl Turning