Aruba IAP-335 User Manual page 86

Table 21: WLAN Configuration Parameters
Parameter
SSID Encoding
Deny inter user
bridging
ESSID
5. Click Next to configure VLAN settings. For more information, see
SSID Profile on page
In the CLI
To configure WLAN settings for an SSID profile:
(Instant AP)(config)# wlan ssid-profile <name>
(Instant AP)(SSID Profile <name>)# essid <ESSID-name>
(Instant AP)(SSID Profile <name>)# type {<Employee>|<Voice>|<Guest>}
(Instant AP)(SSID Profile <name>)# broadcast-filter {All|ARP|Unicast-ARP-Only|Disabled}
(Instant AP)(SSID Profile <name>)# dtim-period <number-of-beacons>
(Instant AP)(SSID Profile <name>)# multicast-rate-optimization
(Instant AP)(SSID Profile <name>)# dynamic-multicast-optimization
(Instant AP)(SSID Profile <name>)# dmo-channel-utilization-threshold
(Instant AP)(SSID Profile <name>)# a-max-tx-rate <rate>
(Instant AP)(SSID Profile <name>)# a-min-tx-rate <rate>
(Instant AP)(SSID Profile <name>)# g-max-tx-rate <rate>
(Instant AP)(SSID Profile <name>)# g-min-tx-rate <rate>
(Instant AP)(SSID Profile <name>)# zone <zone>
(Instant AP)(SSID Profile <name>)# bandwidth-limit <limit>
(Instant AP)(SSID Profile <name>)# per-user-bandwidth-limit <limit>
(Instant AP)(SSID Profile <name>)# air-time-limit <limit>
(Instant AP)(SSID Profile <name>)# wmm-background-dscp <dscp>
(Instant AP)(SSID Profile <name>)# wmm-background-share <share>
(Instant AP)(SSID Profile <name>)# wmm-best-effort-dscp <dscp>
(Instant AP)(SSID Profile <name>)# wmm-best-effort-share <share>
(Instant AP)(SSID Profile <name>)# wmm-video-dscp <dscp>
(Instant AP)(SSID Profile <name>)# wmm-video-share <share>
(Instant AP)(SSID Profile <name>)# wmm-voice-dscp <dscp>
(Instant AP)(SSID Profile <name>)# wmm-voice-share <share>
(Instant AP)(SSID Profile <name>)# rf-band {<2.4>|<5>|<all>}
(Instant AP)(SSID Profile <name>)# content-filtering
(Instant AP)(SSID Profile <name>)# mfp-capable
(Instant AP)(SSID Profile <name>)# mfp-required
(Instant AP)(SSID Profile <name>)# hide-ssid
(Instant AP)(SSID Profile <name>)# out-of-service <def> <name>
(Instant AP)(SSID Profile <name>)# time-range <profile name> {<Enable>|<Disable>}
(Instant AP)(SSID Profile <name>)# inactivity-timeout <interval>
(Instant AP)(SSID Profile <name>)# local-probe-req-thresh <threshold>
86 | Wireless Network Profiles
Description
individually for each IAP in the cluster.
To encode the SSID, select UTF-8. By default, the SSIDs are not encoded.
NOTE: When a wireless SSID is encoded, by default, UTF-8 is added to the access rules
that are active on the SSID. However this does not apply for the access rules that are
configured separately for the SSID. UTF-8 is not supported for wired networks.
When enabled, the bridging traffic between two clients that are connected to the same
SSID on the same VLAN is disabled. The clients can connect to the Internet, but cannot
communicate with each other, and the bridging traffic between the clients is sent to the
upstream device to make the forwarding decision.
Enter the Extended Service Set Identifier (ESSID). If the value defined for ESSID value is not
the same as the profile name, the SSIDs can be searched based on the ESSID value and
not by its profile name.
87.
Configuring VLAN Settings for a WLAN
Aruba Instant 6.5.0.0-4.3.0.0 | User Guide