Connecting Readers; M-In/Out Programmable Input/Output Expander - Bentel Security KYO 320 Installation Manual

11. Re at tach the frontplate.

Connecting Readers

Readers can be lo cated in places where lim ited con trol
of the sys tem is re quired (Arming, A and B Mode
Arming, Dis arming and Stop Alarm op er a tions).
This sys tem sup ports Dig i tal Key and Prox im ity Card
Readers.
Key Readers Key Readers can be flush mounted to
most stan dard do mes tic light-switch/plug-socket out let
boxes (re fer to "Ac ces sory
"INTRODUCTION" for the avail able mod els).
Dig i tal Key Readers must be at least 10 cm apart.
To in stall Key Readers, work care fully through the fol -
low ing steps (see Fig ure on page 13).
1. As sign the Reader Ad dress, then set the BPI Level
and com plete the con nec tions on the ter mi nal
board (re fer to "Con necting BPI Pe riph erals" for in -
struc tions).
2. Fit the Reader in its place ment (use the stan dard
pro ce dure for fit ting do mes tic light-switches and
plug sock ets).
Proximity Readers Prox im ity Readers can be sur face
mounted, or mounted to Mod. 503 out let boxes or sim i -
lar. Prox im ity Readers are fit ted with weather strips
(Pro tec tion Class IP34), there fore, are suit able for out -
door use.
Prox im ity Readers must be at least 50 cm apart.
To in stall Prox im ity Readers, work care fully through the
fol low ing steps (see Fig ure on page 13).
Fi gu re 10 Mounting Key Re a ders
16
3. Re move the screw 90 (if fit ted), then us ing a screw -
4. Drill the holes for the backplate and Seize
5. If you are fit ting a Seize microswitch (Or der Code:
items" in the
6. Se cure the Reader and Seize microswitch bracket
7. As sign the Reader Ad dress, set the BPI Level and
8. Re at tach the frontplate.
Fix the M-IN/OUT In put/Out put Ex pander as close as
pos si ble to the de vices to which it is to be con nected.
The Ex pander is pro vided with a plas tic con tainer for
vis i ble (sur face) mount ing or flush mount ing, as de -
scribed in the fol low ing in struc tions (see Fig ure on
page 14).
1. Re move the knock out (103 or 105 as re quired).
2. – Sur face mount ing: drill the holes for the backplate
3. Pull the wires through the wire en try.
4. Se cure the back box and Seize microswitch
5. Re place the PCB in side the box.
6. Set the Ad dress of the de vice and carry out the con -
to the
Tamper line
driver or sim i lar tool push down on the catch 93 to
re lease the frontplate.
microswitch bracket an chor screws (83 and 88 re -
spec tively).
ASNC-MINI), push it firmly into its lo ca tion (87 in
Fig. 7) then con nect it to the con nec tor 86. En sure
that the Seize microswitch le ver is held firmly in po -
si tion by the bracket tooth.
to the wall.
com plete the con nec tions on the ter mi nal board
(re fer to "Con necting BPI Pe riph erals" for in struc -
tions).

M-IN/OUT Programmable Input/Output Expander

and Seize microswitch bracket an chor screws (106
and 107 re spec tively).
– Flush mount ing to Mod. 503 out let box or sim i lar:
drill the hole for the Seize microswitch bracket an -
chor screw 104. No other drill ing is re quired for
Flush mount ing.
bracket to the wall.
Po si tion the snatch microswitch bracket as shown
in fig ure 9 on page 14, with the con duc tive pin 109
on the back of the con tainer. The pin is de signed to
close the snatch microswitch con tact 96 on the
printed cir cuit (sol der side).
nec tions on ter mi nal board 72, as de scribed in the
para graph "Con nect ing the BPI de vices".