Configure Static Routes For The Management Interface - Dell Force10 Z9000 Configuration Manual

S 6.1.2.17/32 via 6.1.20.2, Gi 5/1
S 11.1.1.0/24 Direct, Nu 0
Direct, Lo 0
--More--
Dell#show ip route static
Destination Gateway
----------- -------
S 2.1.2.0/24 Direct, Nu 0
S 6.1.2.0/24 via 6.1.20.2, Te 5/1/1
S 6.1.2.2/32 via 6.1.20.2, Te 5/1/1
S 6.1.2.3/32 via 6.1.20.2, Te 5/1/1
S 6.1.2.4/32 via 6.1.20.2, Te 5/1/1
S 6.1.2.5/32 via 6.1.20.2, Te 5/1/1
S 6.1.2.6/32 via 6.1.20.2, Te 5/1/1
S 6.1.2.7/32 via 6.1.20.2, Te 5/1/1
S 6.1.2.8/32 via 6.1.20.2, Te 5/1/1
S 6.1.2.9/32 via 6.1.20.2, Te 5/1/1
S 6.1.2.10/32 via 6.1.20.2, Te 5/1/1
S 6.1.2.11/32 via 6.1.20.2, Te 5/1/1
S 6.1.2.12/32 via 6.1.20.2, Te 5/1/1
S 6.1.2.13/32 via 6.1.20.2, Te 5/1/1
S 6.1.2.14/32 via 6.1.20.2, Te 5/1/1
S 6.1.2.15/32 via 6.1.20.2, Te 5/1/1
S 6.1.2.16/32 via 6.1.20.2, Te 5/1/1
S 6.1.2.17/32 via 6.1.20.2, Te 5/1/1
S 11.1.1.0/24 Direct, Nu 0
Direct, Lo 0
--More--
Dell Networking OS installs a next hop that is on the directly connected subnet of current IP address on the interface (for example, if
interface TenGigabitEthernet 1/1 is on 172.31.5.0 subnet, Dell Networking OS installs the static route).
Dell Networking OS also installs a next hop that is not on the directly connected subnet but which recursively resolves to a next hop
on the interface's configured subnet. For example, if te 1/1 has ip address on subnet 2.2.2.0 and if 172.31.5.43 recursively resolves
to 2.2.2.0, Dell Networking OS installs the static route.
• When the interface goes down, Dell Networking OS withdraws the route.
• When the interface comes up, Dell Networking OS re-installs the route.
• When the recursive resolution is "broken," Dell Networking OS withdraws the route.
• When the recursive resolution is satisfied, Dell Networking OS re-installs the route.

Configure Static Routes for the Management Interface

When an IP address that a protocol uses and a static management route exists for the same prefix, the protocol route takes
precedence over the static management route.
To configure a static route for the management port, use the following command.
• Assign a static route to point to the management interface or forwarding router.
CONFIGURATION mode
management route ip-address mask {forwarding-router-address | ManagementEthernet slot/
port}
Example of the show ip route static Command
To view the configured static routes for the management port, use the show ip management-route command in EXEC
privilege mode.
Dell#show ip route static
Destination Gateway
----------- -------
S 2.1.2.0/24 Direct, Nu 0
S 6.1.2.0/24 via 6.1.20.2, Te 5/1
1/0 00:02:30
0/0 00:02:30
Dist/Metric Last Change
----------- -----------
0/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
1/0 00:02:30
0/0 00:02:30
Dist/Metric Last Change
----------- -----------
0/0 00:02:30
1/0 00:02:30
319
IPv4 Routing