Copy Configuration Files Using Snmp - Dell Force10 Z9000 Configuration Manual

%ECFM-5-ECFM_MAC_STATUS_ALARM: MAC Status Defect detected by MEP 1 in Domain
provider at Level 4 VLAN 3000
%ECFM-5-ECFM_REMOTE_ALARM: Remote CCM Defect detected by MEP 3 in Domain
customer1 at Level 7 VLAN 1000
%ECFM-5-ECFM_RDI_ALARM: RDI Defect detected by MEP 3 in Domain customer1 at
Level 7 VLAN 1000
entity
Enable entity change traps
Trap SNMPv2-MIB::sysUpTime.0 = Timeticks: (1487406) 4:07:54.06,
SNMPv2-MIB::snmpTrapOID.0 = OID: SNMPv2-SMI::mib-2.47.2.0.1,
SNMPv2-SMI::enterprises.6027.3.6.1.1.2.0 = INTEGER: 4
Trap SNMPv2-MIB::sysUpTime.0 = Timeticks: (1488564) 4:08:05.64,
SNMPv2-MIB::snmpTrapOID.0 = OID: SNMPv2-SMI::mib-2.47.2.0.1,
SNMPv2-SMI::enterprises.6027.3.6.1.1.2.0 = INTEGER: 5
Trap SNMPv2-MIB::sysUpTime.0 = Timeticks: (1489064) 4:08:10.64,
SNMPv2-MIB::snmpTrapOID.0 = OID: SNMPv2-SMI::mib-2.47.2.0.1,
SNMPv2-SMI::enterprises.6027.3.6.1.1.2.0 = INTEGER: 6
Trap SNMPv2-MIB::sysUpTime.0 = Timeticks: (1489568)
4:08:15.68,SNMPv2-MIB::snmpTrapOID.0 = OID: SNMPv2-SMI::mib-2.47.2.0.1,
SNMPv2-SMI::enterprises.6027.3.6.1.1.2.0 = INTEGER: 7
<cr>
SNMP Copy Config Command Completed
%RPM0-P:CP %SNMP-4-RMON_RISING_THRESHOLD:
SNMP OID <oid>
%RPM0-P:CP %SNMP-4-RMON_FALLING_THRESHOLD:
SNMP OID <oid>
%RPM0-P:CP %SNMP-4-RMON_HC_RISING_THRESHOLD:
alarm from SNMP OID <oid>

Copy Configuration Files Using SNMP

To do the following, use SNMP from a remote client.
• copy the running-config file to the startup-config file
• copy configuration files from the Dell Networking system to a server
• copy configuration files from a server to the Dell Networking system
You can perform all of these tasks using IPv4 or IPv6 addresses. The examples in this section use IPv4 addresses; however, you can
substitute IPv6 addresses for the IPv4 addresses in all of the examples.
The following table lists the relevant MIBs for these functions are.
Table 51. MIB Objects for Copying Configuration Files via SNMP
MIB Object
copySrcFileType
copySrcFileLocation
696
Simple Network Management Protocol (SNMP)
OID
.1.3.6.1.4.1.6027.3.5.1.1.1.1.2
.1.3.6.1.4.1.6027.3.5.1.1.1.1.3
STACKUNIT0 rising threshold alarm from
STACKUNIT0 falling threshold alarm from
STACKUNIT0 high-capacity rising threshold
Object Values
1 = Dell Networking OS file
2 = running-config
3 = startup-config
1 = flash
2 = slot0
Description
Specifies the type of file to
copy from. The range is:
• If copySrcFileType is
running-config or startup-
config, the default
copySrcFileLocation is
flash.
• If copySrcFileType is a
binary file, you must also
specify
copySrcFileLocation and
copySrcFileName.
Specifies the location of source
file.