Sample Configuration - Dell Force10 Z9000 Configuration Manual

seq 15 redirect tunnel 2 udp 155.55.0.0/16 host 144.144.144.144, Track 1 [up], Next-hop
reachable (via Te 1/32)
seq 35 redirect 155.1.1.2 track 5 ip 7.7.7.0/24 8.8.8.0/24, Track 5 [up], Next-hop
reachable (via Po 5)
seq 30 redirect 155.1.1.2 track 6 icmp host 8.8.8.8 any, Track 5 [up], Next-hop reachable
(via Po 5)
seq 35 redirect 42.1.1.2 icmp host 8.8.8.8 any, Next-hop reachable (via Vl 20)
seq 40 redirect 43.1.1.2 tcp 155.55.2.0/24 222.22.2.0/24, Next-hop reachable (via Vl 30)
seq 45 redirect 31.1.1.2 track 200 ip 12.0.0.0 255.0.0.197 13.0.0.0 255.0.0.197, Track 200
[up], Next-hop reachable (via Te 1/32)
[up], Next-hop reachable (via Vl 20)
[up], Next-hop reachable (via Po 5)
[up], Next-hop reachable (via Po 7)
[up], Next-hop reachable (via Te 2/18)
[up], Next-hop reachable (via Te 2/19)
Use the show ip redirect-list (without the list name) to display all the redirect-lists configured on the device.
Dell#show ip redirect-list
IP redirect-list rcl0:
Defined as:
seq 5 permit ip 200.200.200.200 200.200.200.200 199.199.199.199 199.199.199.199
seq 10 redirect 1.1.1.2 tcp 234.224.234.234 255.234.234.234 222.222.222.222/24 eq 40 ack,
Next-hop reachable
(via Te 2/1),
Applied interfaces:
Te 2/2
NOTE: If, the redirect-list is applied to an interface, the output of show ip redirect-list redirect-list-name command
displays reachability status for the specified next-hop.
Showing CAM PBR Configuration Example :
Dell#show cam pbr stack-unit 1 port-set 0
TCP Flag: Bit 5 - URG, Bit 4 - ACK, Bit 3 - PSH, Bit 2 - RST, Bit 1 - SYN, Bit 0 - FIN
Cam Port VlanID Proto Tcp
Index Flag Port Port
--------------------------------------------------------------------------------------------
---------------------
06080 0 N/A IP
199.199.199.199 N/A
06081 0 N/A TCP
00:00:00:00:00:09 8/1

Sample Configuration

The following configuration is an example for setting up a PBR. These are not comprehensive directions. They are intended to give
you a some guidance with typical configurations. You can copy and paste from these examples to your CLI. Be sure you make the
necessary changes to support your own IP Addresses, Interfaces, Names, etc.
Graphic illustration of the configuration shown below:
The Redirect-List GOLD defined in this example, creates the following rules:
• description Route Gold traffic to the DS3.
• seq 5 redirect 10.99.99.254 ip 192.168.1.0/24 any " Redirect to next-hop router IP 10.99.99.254 any traffic originating in
192.168.1.0/24"
• seq 10 redirect 10.99.99.254 ip 192.168.2.0/24 any " Redirect to next-hop router IP 10.99.99.254 any traffic originating in
192.168.2.0/24"
Src Dst
MAC Port
0x0 0 0 200.200.200.200 200.200.200.200 199.199.199.199
NA
0x10 0 40 234.234.234.234 255.234.234.234 222.222.222.222/24
SrcIp DstIp Next-hop
, Track 200
, Track 200
, Track 200
, Track 200
, Track 200
Egress
Policy-based Routing (PBR)
529