Safe Title Settings; Displaying A List Of Transition Rates And Changing The Settings - Sony MVS-8000X SystemMVS-7000X System User Manual

Enabling or disabling control from the
editing keyboard
1
In the menu control block, press the top menu
selection button [MISC], then select VF1 'Enable' and
HF2 'Plug-In Editor.'
The Misc >Enable >Plug-In Editor menu appears.
2
In the <Control From Plug-In Editor> group, press
[Editor Enable].
Each time you press the button toggles between enable
and disable.
To enable control of the preview bus only
When control from the editing keyboard is disabled (when
[Editor Enable] is set to Disable), to enable control of the
preview bus only, press [PVW Bus Enable] in the
<Control From Plug-In Editor> group.

Safe Title Settings

Switching the safe title function on or off
1
In the menu control block, press the top menu
selection button [MISC] and select VF2 'Safe Title.'
The Misc >Safe Title menu appears.
2
Using any of the following methods, select the signal
to which the settings apply.
• Directly press the list in the status area.
• Press the arrow keys to scroll the reverse video
cursor.
• Turn the knob to make the setting.
Knob Parameter Adjustment
1 Output
Notes
• It is not possible to change the setting for the output
for which the safe title is set off in the Setup menu.
• The safe title function cannot be used for output
signals for which through mode is set to Enable in
the Setup menu.
For more information about the Setup menu settings
referred to above, see "Signal Input Settings (Input
Menu)" and "Signal Output Settings (Output Menu)"
in Chapter 20 (Volume 2).
3
Press [Safe Title] to set it on or off.
234
Misc Menu Operations
Setting values
Signal to which 1 to 48
the settings
apply
Displaying a List of Transition Rates
and Changing the Settings
In the Misc >Transition >Key/ME/FTB menu, for each
bank you can display a list of the M/E (or PGM/PST)
transition rates and independent key (or DSK) transition
rates, and change the settings.
These settings are linked to the other transition rate setting
operations.
You can also display and set the fade-to-black transition
rate.
Displaying the Transition >Key/ME/FTB
menu
In the menu control block, press the top menu selection
button [MISC], then select VF3 'Transition' and HF1
'Key/ME/FTB.'
The Misc >Transition >Key/ME/FTB menu appears.
About the Transition >Key/ME/FTB menu display
The display of the independent key transition rate in the
Misc >Transition >Key/ME/FTB menu depends on the
selection in the <Key Transition> group of the
Engineering Setup >Switcher >Transition menu for each
of the M/E and PGM/PST banks.
When [Same] (On direction and Off direction settings
the same) is selected in the <Key Transition>
group: Only "Key" (or "DSK" in the PGM/PST bank)
appears.
When [Independ] (On direction and Off direction
settings independent) is selected in the <Key
Transition> group: "Key(On)" and "Key(Off)" each
appear. In the case of the PGM/PST bank, "DSK(On)"
and "DSK(Off)" appear.
For details, see "Settings Relating to Video Switching
(Transition Menu)" in Chapter 20 (Volume 2).
Setting the transition rate in the Transition
>Key/ME/FTB menu
To set the M/E transition rate
For example, to make the settings for the M/E-1 bank, use
the following procedure.
1
Press in the list in the status area of the Misc
>Transition >Key/ME/FTB menu, to select M/E-1.
2
In the <Transition Rate> group, press [Transition].
3
Turn the knob to set the number of frames.
Knob Parameter Adjustment
1 Transition Transition rate
Rate
Setting values
0 to 999
(frames)