Table of Contents
Advertisement
Setting the surface where light strikes the
image
1
In the DME menu, select VF5 'Light/Trail
.'
'Spot Lighting
The Spot Lighting menu appears.
2
Press [Spot Lighting], turning it on.
3
Set the following parameter.
Knob Parameter Adjustment
1
Total
Brightness of
Ambient
whole image
• Lowering the brightness of the image makes
Spotlighting more effective.
• The Total Ambient setting is shared with the
Lighting function.
4
In the <Surface Select> group, select the state of the
surface struck by the light.
Flat: The image surface is unchanged, causing the
selected light source to appear as the effect.
Texture: A texture appears on the surface of the
image.
Non Linear: The Spotlighting effect is applied to an
area to which a DME nonlinear effect is applied.
Notes
• The BZDM-9050 Texture Lighting Software (for
MVE-9000) is required to enable Texture or Non
Linear.
An install key must be entered to use the software.
For details, see "Installation and Device Setup
(Install/Unit Config Menu)" in Chapter 18
(Volume 2).
• The Spotlighting Non Linear setting is effective for
the following nonlinear effects. For any other
nonlinear effect, the result of selecting the Non
Linear setting is the same as selecting Flat.
Wave, Mosaic Glass, Flag, Ripple, Lens,
Panorama, Page Turn, Roll.
5
If you selected Texture or Non Linear in step 4, set the
following parameters.
Parameters when you selected Texture
• SD format
Knob Parameter Adjustment
Movement in
1
X
X-axis direction
Movement in
2
Y
Y-axis direction
Knob Parameter Adjustment
3
'
and HF6
4
5
a) Minus moves left, plus moves right.
b) Minus moves down, plus moves up.
c) Plus emphasizes bumps in texture, minus emphasizes depressions.
0.00 is a flat surface.
Setting values
• HD format
0.00 to 100.00
Knob Parameter Adjustment
1
2
3
4
5
a) Minus moves left, plus moves right.
b) Minus moves down, plus moves up.
c) Plus emphasizes bumps in texture, minus emphasizes depressions.
0.00 is a flat surface.
Parameters when you selected Non Linear
Knob Parameter Adjustment
5
a) Light appears from Z direction. At –100.00 the light goes deepest, at
+100.00 the whole image is lit like a flat effect.
6
If you selected Texture in step 4, select the pattern as
explained in the next section "To select a texture
pattern."
7
If you selected Texture in step 4, select the way it is
applied in the <Surface Axis> group.
Move: The texture moves together with the DME
Fix: The texture does not move, even if the DME
For the difference between these application methods,
see "Coordinate axis on surface of image" (page 336).
Setting values
a)
–8.00 to +8.00
Notes
If Non Linear is selected in the <Surface Select>
–6.00 to +6.00
b)
group, Fix is disabled. Behavior is the same as Move.
Size X
Image size in
X-axis direction
Size Y
Image size in
Y-axis direction
Amp
Emphasize
bumps and
depressions
Movement in
X
X-axis direction
Y
Movement in
Y-axis direction
Size X
Image size in
X-axis direction
Size Y
Image size in
Y-axis direction
Amp
Emphasize
bumps and
depressions
Distance of light –100.00 to
Amp
image.
image moves.
Applying Special Effects (Lighting and Recursive Effects)
Setting values
0.50 to 16.00
0.50 to 16.00
–100.00 to
c)
+100.00
Setting values
–32.00 to
a)
+32.00
–24.00 to
b)
+24.00
0.50 to 16.00
0.50 to 16.00
–100.00 to
c)
+100.00
Setting values
a)
+100.00
339
Advertisement
Table of Contents
