Sony MVS-8000X SystemMVS-7000X System User Manual page 188

• Wave/Ripple: wave and ripple
• Page Turn/Roll: page turn and page roll
• Frame I/O/P in P: frame in/out and picture-in-
picture
• 2D Trans/3D Trans: 2D trans and 3D trans
• Sparkle/Split Slide: sparkle and split slide
• Mosaic/Defocus: mosaic and defocus
• Brick: brick
• User Program: user programmable DME
Selectable DME wipe pattern groups in one-
channel mode: All of the above groups except for
Brick.
Selectable DME wipe pattern groups in two-
channel mode: Slide/Squeeze, Page Turn/Roll,
Frame I/O, PinP, 3D Trans, Brick and User
Program.
Selectable DME wipe pattern groups in three-
channel mode: User Program and Brick.
For details of DME wipe patterns, see "Types of DME
Wipe Pattern" (page 183) and "DME Wipe Pattern
List" (page 361) in Appendix.
The patterns from the selected pattern group appear on
the screen.
3
Press the button to select the desired pattern.
Adjusting DME wipe pattern parameters
Of the DME wipe patterns, the following have parameters
that can be adjusted.
When Brick (for two channels) is selected
(pattern numbers 2801 to 2804, 2811 to 2814)
Knob Parameter
1 Side V Size X
2 Side V Size Y
3 Height
4 Center X
5 Center Y
a) The horizontal center position of the video pasted on Side V. At –100.00
the center is at the left edge of the screen, and at +100.00 the center is at
the right edge of the screen.
b) The vertical center position of the video pasted on Side V. At –100.00 the
center is at the bottom edge of the screen, and at +100.00 the center is at
the top edge of the screen.
188
Basic Procedure for DME Wipe Settings
Adjustment Setting values
Horizontal 0.01 to 8.00
magnification
Vertical 0.01 to 8.00
magnification
Height of brick 0.01 to 100.00
–100.00 to
Horizontal
a)
+100.00
center position
–100.00 to
Vertical center
b)
+100.00
position
When Frame in-out (for two channels) is selected
• Pattern numbers 2851 to 2854
Knob Parameter Adjustment
5 Delay Timing for
video selected
on a utility bus
to appear on
the screen
• Pattern numbers 2861 to 2864
Knob Parameter Adjustment
1 Rot X Rotation about
the Y axis
(horizontal
direction)
2 Rot Y Rotation about
the X axis
(vertical
direction)
3 Rot Z Rotation about
the Z axis
5 Delay Timing for
video selected
on a utility bus
to appear on
the screen
When Brick (for three channels) is selected
(pattern number 3601)
Parameter group [1/2]
Knob Parameter Adjustment
1 Side V Size X Side V
horizontal
magnification
2 Side V Size Y Side V vertical
magnification
3 Height Height of brick
4 Side V Center Side V
horizontal
X
center position
5
Side V Center Side V vertical
Y center position
a) Shared with knob 3 for parameter group 2
b) The horizontal center position of the video pasted on Side V. At –100.00
the center is at the left edge of the screen, and at +100.00 the center is at
the right edge of the screen.
c) The vertical center position of the video pasted on Side V. At –100.00 the
center is at the bottom edge of the screen, and at +100.00 the center is at
the top edge of the screen.
Parameter group [2/2]
Knob Parameter Adjustment
1 Side H Size X Side H
horizontal
magnification
2 Side H Size Y Side H vertical
magnification
Setting values
–100.00 to
+100.00
Setting values
–100.00 to
+100.00
–100.00 to
+100.00
–100.00 to
+100.00
–100.00 to
+100.00
Setting values
0.01 to 8.00
0.01 to 8.00
0.01 to
a)
100.00
–100.00 to
b)
+100.00
–100.00 to
c)
+100.00
Setting values
0.01 to 8.00
0.01 to 8.00