Table of Contents
Advertisement
The cross-point button you pressed flashes green, and
the register you recalled in step 1 is assigned to the
button. The [MCRO ONLY SET] button goes off.
Without switching to macro only mode in step 2, if
you hold down the [PRE MCRO] and [POST MCRO]
buttons together and press the desired button, it is
possible to set a macro attachment in macro only mode
for that button.
To check macro attachment settings
Hold down the [PRE MCRO] button or [POST MCRO]
button. While it is held down, buttons for which macro
attachments are set flash as follows.
While the [PRE MCRO] button is held down:
• Buttons set in pre macro mode: flash amber
• Buttons set in macro only mode: flash green
While the [POST MCRO] button is held down:
• Buttons set in post macro mode: flash amber
• Buttons set in macro only mode: flash green
Setting a macro attachment to a fader lever
You can set a macro attachment to any particular position
of a fader lever in the transition control block.
Notes
• In macro only mode it is not possible to set a macro
attachment.
• It is not possible to set a macro attachment to a fader
lever in the keyframe control block or downstream key
control block.
• For a split fader, you can set a macro attachment to the
main split fader.
1
Recall the macro register (1 to 250) that you want to
assign to the fader lever (see page 500).
2
Move the fader lever to the position where you want to
set the macro attachment.
3
Hold down the [PRE MCRO] or [POST MCRO]
1)
button
in the cross-point control block, and press the
[LIMIT SET] or [PRIOR SET] button in the control
block containing the fader lever operated in step 2.
1) Only when setting a macro attachment to the start point or end point
of fader lever operation, use [PRE MCRO] and [POST MCRO] in
distinction, as follows.
To set the operation start point (0%): hold down [PRE MCRO] for
the operation.
To set the operation end point (100%): hold down [POST MCRO]
for the operation.
This assigns the register recalled in step 1 to the fader
lever position selected in step 2.
To check a macro attachment setting
Hold down the [PRE MCRO] or [POST MCRO] button in
the cross-point control block. While it is held down, the
fader lever position where the macro attachment is set
appears in the following places.
• Transition indicator in the transition execution
section: The indicator lights at the position where the
macro attachment is set.
• Transition rate indication in the transition execution
section: This shows the fader lever position where the
macro attachment is set, as a percentage value (fader
lever start position as 0%, end position 100%).
Removing macro attachment settings
To cancel a macro attachment to a button
Hold down the [PRE MCRO] button or [POST MCRO]
button, and press a button that is flashing in the
background A row. The button for which the macro
attachment is set stops flashing and goes off, and this
removes the setting.
To cancel a macro attachment to a fader lever
Hold down the [PRE MCRO] or [POST MCRO] button in
the cross-point control block, and press the [LIMIT SET]
or [PRIOR SET] button in the control block containing the
To delete individual macro attachment settings
You can delete individual settings of a macro attachment
assigned to a button.
1
In the Macro menu, select VF2 'Attachment.'
The Attachment menu appears.
2
In the list, select the relevant data by any of the
following methods.
• Press directly on the menu macro register
configuration list.
• Press the arrow keys to scroll the reverse video
cursor.
• Turn the knob.
Knob
Parameter
Adjustment
1
No
Number to be
selected
3
Press [Delete].
A confirmation message appears.
4
To confirm the deletion, select [Yes]. To cancel, select
[No].
To remove all macro attachment settings in a
single operation
1
In the Macro menu, select VF2 'Attachment.'
2
Press [All Clear].
Setting values
1 to maximum
value
519
Macro Attachment Assigning
Advertisement
Table of Contents
