Husqvarna TE 250-310 2012 I.E. Workshop Manual page 355

TE 250 - 310 2012 I.E. / TE 250 - 310 2012 I.E. USA
Lubrication
Screw TCEI M5x0.8 L20
Oil drain plug M14x1.5
Drilled screw TEF M8x1.25 (alu-
minium)
Oil filler plug
Fuel system
Screw M6x1 L20
Electrical System
Screw TEF M6x1-CH8-L20
Screw TCEI M5-L12
Screw TCEI M4-L30
Screw TCEI M5-L20
Flanged nut M12x1
Screw TEF M6x1-CH8-L20
Screw TCEI M5x08 L8
Spark plug
Clutch
Nut M16x1-CH27-SP7
Screw TEF M6x1-CH8-L20
Screw TCEI M6-L16
Screw TCEI M6-L12
Starting system
Screw TCEI M5-L30
Short nut M6x1
Screw TCEI M5-L20
Screw TEF M8-L.15
Screw TSEI M6 L14
Gearbox
Nut M16x1
Gear shift control
Selector drum rtng screw M8x1.25
Screw TSEI M6-L14
Screw TEF M6-L14
Screw TEF M5x0.8-CH8-L12
Screw TEF M6x1-CH8-L20
Cooling
M5 x 8
Screw TCEI M5
Cheese-headed Phillips screw M4-
L12
(*): Smear some graphite grease on spark plug thread, do it fully home finger tight then tighten it to 10÷12 Nm torque. Loosen the
spark plug then tighten it again to 10÷12 Nm.
TIGHTENING TORQUE FIGURES
TC 250 2012 - TC 250 2012 I.E. USA
TXC 250 - 310 2012 I.E. USA
Oil pump body
Pipe
Fastening intake manifold
Coil to chassis
(TE - TXC)
Stator (use LOCTITE 272)
Fastening stator (fit with LOCTITE 272) (TC)
Pick-up sensor (use LOCTITE
Flywheel
Regulator to chassis
Fastening coil safety plate (TC)
(fit with LOCTITE 272 - 270)
M10x1
Clutch hub
Pressure plate
Clutch cylinder
Clutch cylinder
Starter motor (TE - TXC)
Gear to starter motor shaft
Bevel drive body
Kick start lever
(TE - TXC)
Fastening start-up lever (TC) (+LOCTITE 272)
Sprocket
Use LOCTITE 270 (or LOCTITE 243)
Selector rtng plate (+LOCTITE 243)
Selector rtng plate (+LOCTITE 243)
Indicator
Gear shift lever
Water pump impeller (+LOCTITE 243)
Cover
Fitting (+LOCTITE 243)
(TE - TXC)
)
272 - 270
(+LOCTITE 270)
(TE - TXC)
(TE - TXC)
(+LOCTITE 272)
X.3
6 Nm 0.6 Kgm
25 Nm 2.55 Kgm
8 Nm 0.8 Kgm
Finger-tight
8 Nm 0.8 Kgm
8 Nm 0.8 Kgm
6 Nm 0.6 Kgm
4 Nm 0.4 Kgm
6 Nm 0.6 Kgm
75 Nm 7.65 Kgm
8 Nm 0.8 Kgm
6 Nm 0.6 Kgm
(*)
65 Nm 6.6 Kgm
8 Nm 0.8 Kgm
8 Nm 0.8 Kgm
8 Nm 0.8 Kgm
6 Nm 0.6 Kgm
8 Nm 0.8 Kgm
6 Nm 0.6 Kgm
25 Nm 2.55 Kgm
10 Nm 1.0 Kgm
90 Nm 9.2 Kgm
25 Nm 2.55 Kgm
8 Nm 0.8 Kgm
8 Nm 0.8 Kgm
6 Nm 0.6 Kgm
8 Nm 0.8 Kgm
8 Nm 0.8 Kgm
6 Nm 0.6 Kgm
3 Nm 0.3 Kgm
Workshop Manual Ed. 12-2011