Husqvarna TE 250i EU 2020 Owner's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Motorcycle
  5. TE 250i EU 2020
  6. Owner's manual

Husqvarna TE 250i EU 2020 Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
OWNER'S MANUAL 2020
TE 250i
TE 300i
TE 300i JARVIS EDITION
Art. no. 3402407en

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna TE 250i EU 2020

Summary of Contents for Husqvarna TE 250i EU 2020

  • Page 1 OWNER'S MANUAL 2020 TE 250i TE 300i TE 300i JARVIS EDITION Art. no. 3402407en...
  • Page 3 DEAR HUSQVARNA MOTORCYCLES CUSTOMER Congratulations on your decision to purchase a Husqvarna motorcycle. You are now the owner of a state-of- DEAR HUSQVARNA MOTORCYCLES CUSTOMER the-art sports vehicle that will continue giving you pleasure for a long time if you maintain it properly.

  • Page 4: Table Of Contents

    TABLE OF CONTENTS TABLE OF CONTENTS 6.14 Overview of indicator lamps (All EU MEANS OF REPRESENTATION......6 models) ..........20 Symbols used ........6 6.15 Overview of indicator lamps (All US Formats used ........6 models) ..........20 6.16 Opening fuel tank filler cap ....21 SAFETY ADVICE ..........
  • Page 5 TABLE OF CONTENTS RIDING INSTRUCTIONS ......... 38 12.2 Removing the motorcycle from the lift stand ..........56 Checks and maintenance measures 12.3 Bleeding the fork legs ......56 when preparing for use ....... 38 12.4 Cleaning the dust boots of the fork Starting the vehicle ......
  • Page 6 TABLE OF CONTENTS 12.43 Changing the hydraulic clutch COOLING SYSTEM........121 fluid ..........86 16.1 Cooling system ......... 121 12.44 Removing the engine guard....87 16.2 Checking the antifreeze and 12.45 Installing the engine guard....87 coolant level........121 BRAKE SYSTEM ..........88 16.3 Checking the coolant level....
  • Page 7 TABLE OF CONTENTS 22.7 Fork........... 152 22.8 Shock absorber ........ 152 22.9 Chassis tightening torques ....153 SUBSTANCES..........155 AUXILIARY SUBSTANCES......157 STANDARDS ..........159 INDEX OF SPECIAL TERMS ......160 LIST OF ABBREVIATIONS ......161 LIST OF SYMBOLS ........162 28.1 Red symbols ........

  • Page 8: Means Of Representation

    1 MEANS OF REPRESENTATION Symbols used The meaning of specific symbols is described below. Indicates an expected reaction (e.g. of a work step or a function). Indicates an unexpected reaction (e.g. of a work step or a function). All work marked with this symbol requires specialist knowledge and technical understand- ing.

  • Page 9: Safety Advice 2

    SAFETY ADVICE 2 Use definition – intended use (All EU models) This vehicle has been designed and built to withstand the normal stresses and strains of racing. This vehi- cle complies with the currently valid regulations and categories of the top international motorsports organi- zations.

  • Page 10: Degrees Of Risk And Symbols

    2 SAFETY ADVICE Degrees of risk and symbols Danger Identifies a danger that will immediately and invariably lead to fatal or serious permanent injury if the appropriate measures are not taken. Warning Identifies a danger that is likely to lead to fatal or serious injury if the appropriate measures are not taken.

  • Page 11: Protective Clothing

    – Always wear protective clothing that is in good condition and meets the legal regulations. In the interest of your own safety, Husqvarna Motorcycles recommends that you only operate the vehicle while wearing protective clothing. Work rules Unless specified otherwise, the ignition must be turned off during all work (models with ignition lock, models with remote key) or the engine must be at a standstill (models without ignition lock or remote key).

  • Page 12: Owner's Manual

    The Owner's Manual is an important component of the vehicle and must be handed over to the new owner if the vehicle is sold. The Owner's Manual is also available for download from your authorized Husqvarna Motorcycles dealer and on the Husqvarna Motorcycles website.

  • Page 13: Important Notes 3

    IMPORTANT NOTES 3 Manufacturer and implied warranty The work prescribed in the service schedule must only be carried out in an authorized Husqvarna Motorcy- cles workshop and confirmed in the Husqvarna Motorcycles Dealer.net, as otherwise all warranty claims will be void. Damage or secondary damage caused by tampering with and/or conversions on the vehicle are not covered by the manufacturer warranty.

  • Page 14: Customer Service

    3 IMPORTANT NOTES Customer service Your authorized Husqvarna Motorcycles dealer will be happy to answer any questions you may have regarding your vehicle and Husqvarna Motorcycles. A list of authorized Husqvarna Motorcycles dealers can be found on the Husqvarna Motorcycles website.

  • Page 15: View Of Vehicle 4

    VIEW OF VEHICLE 4 View of vehicle, front left (example) H03646-10 Clutch lever ( p. 17) Fuel tank filler cap Air filter box cover Engine number ( p. 15) Side stand ( p. 24) Shift lever ( p. 23)

  • Page 16: View Of Vehicle, Rear Right (Example)

    4 VIEW OF VEHICLE View of vehicle, rear right (example) H03647-10 2-stroke oil tank cap Switch-off button ( p. 17) (All EU models) p. 18) (All US models) Switch-off button ( Horn button ( p. 18) (All EU models) Light switch ( p.

  • Page 17: Serial Numbers 5

    SERIAL NUMBERS 5 Vehicle identification number The vehicle identification number is stamped on the right side of the steering head. 401945-10 Type label (All EU models) Type label is fixed to the front of the steering head. 401946-10 Key number (All EU models) Key number for the steering lock is stamped on a tag on the key ring.

  • Page 18: Fork Article Number

    5 SERIAL NUMBERS Fork article number Fork article number is stamped on the inside of the axle clamp. 401947-10 Shock absorber article number Shock absorber article number is stamped on the top of the shock absorber above the adjusting ring towards the engine side. H02222-10...

  • Page 19: Controls 6

    CONTROLS 6 Clutch lever Clutch lever is fitted on the handlebar on the left. The clutch is activated hydraulically and adjusts itself automati- cally. H03648-10 Hand brake lever Hand brake lever is fitted on the right side of the handlebar. The front brake is engaged using the hand brake lever.

  • Page 20: Switch-Off Button (All Us Models)

    6 CONTROLS Switch-off button (All US models) Switch-off button is fitted on the left side of the handlebar. Possible states is in the basic position – In this • The switch-off button position, the ignition circuit is closed and the engine can be started.

  • Page 21: Turn Signal Switch (All Eu Models)

    CONTROLS 6 Turn signal switch (All EU models) The turn signal switch is fitted on the left side of the handle- bar. Possible states Turn signal light off – The turn signal switch is in the central position. Left turn signal on – The turn signal switch is turned to the left.

  • Page 22: Map Switch

    Malfunction indicator lamp lights up/flashes yellow – The OBD has detected a malfunction in the vehicle electronics. Come safely to a halt, and contact an authorized Husqvarna Motorcycles workshop. H03657-10 The fuel level warning lamp lights up yellow – The fuel level has reached the reserve mark.

  • Page 23: Opening Fuel Tank Filler Cap

    CONTROLS 6 6.16 Opening fuel tank filler cap Danger Fire hazard Fuel is highly flammable. The fuel in the fuel tank expands when warm and can escape if overfilled. – Do not refuel the vehicle in the vicinity of open flames or lit cigarettes. –...

  • Page 24: Opening 2-Stroke Oil Tank Cap

    6 CONTROLS 6.18 Opening 2-stroke oil tank cap – Fold loop upward. – Turn the 2-stroke oil tank cap counterclockwise and pull it V01647-10 6.19 Closing 2-stroke oil tank cap – Put the 2-stroke oil tank cap on and turn it clockwise. –...

  • Page 25: Idle Speed Adjusting Screw

    CONTROLS 6 6.21 Idle speed adjusting screw The idle setting of the throttle valve body substantially influences the vehicle’s starting behavior, a stable idle speed, and the vehi- cle’s response when the throttle is opened. An engine with a correctly set idle speed is easier to start than an engine with the idle speed set incorrectly.

  • Page 26: Side Stand

    6 CONTROLS 6.24 Side stand The side stand is located on the left of the vehicle. 401943-10 The side stand is used for parking the motorcycle. Info When you are riding, side stand must be folded up and secured with rubber strap 401944-10 6.25 Steering lock (All EU models)

  • Page 27: Unlocking The Steering (All Eu Models)

    CONTROLS 6 6.27 Unlocking the steering (All EU models) – Insert the key for the steering lock into the steering lock, turn it to the left, pull it out, and turn it to the right. Pull out the key for the steering lock. The handlebar can now be moved again.

  • Page 28: Combination Instrument

    Battery voltage of the combination instrument – The battery voltage of the combination instrument is too low. Change combination instrument battery. Service – A service is due. Contact an authorized Husqvarna Motorcycles workshop. 401901-01 Adjusting the combination instrument Condition The motorcycle is stationary.

  • Page 29: Setting The Kilometers Or Miles

    COMBINATION INSTRUMENT 7 – Wait for 5 seconds. The combination instrument changes to the next menu item. The symbol flashes. – Press one of the buttons to select the 24h or 12h display of the clock. 401911-01 – Wait for 5 seconds. The combination instrument changes to the next menu item.

  • Page 30: Setting The Clock

    7 COMBINATION INSTRUMENT – Press both buttons for 3–5 seconds. The Setup menu is displayed. The UNIT display flashes. – Press one of the buttons to select UNIT for the speed in kilo- meters KM/H or miles M/H. 401909-01 Setting the clock Condition The motorcycle is stationary.

  • Page 31: Speed, Time, And Dst Distance 1

    COMBINATION INSTRUMENT 7 Switching off the service interval display – Press and hold the left button. off appears in the display. 401914-01 Speed, time, and DST distance 1 – Press one of the buttons until DST appears on the combina- tion instrument.

  • Page 32: Avg Average Speed, Art Operating Hours, And Odo Total Distance Covered

    7 COMBINATION INSTRUMENT Press the left DST2 can be preset to a value between 0.0 button for 3 – and 39999.9 by pressing the buttons. 5 seconds. Press the Next display mode right button briefly. Press the DST2 is reset to 0.0. right button for 3 –...

  • Page 33: Preparing For Use 8

    When using your motorcycle, remember that others may feel disturbed by excessive noise. – Make sure that the pre-sale inspection work has been carried out by an authorized Husqvarna Motorcycles workshop. You will receive a delivery certificate when the vehicle is handed over.

  • Page 34: Running In The Engine

    8 PREPARING FOR USE – Adjust the basic position of the hand brake lever. ( p. 88) – Adjust the basic position of the foot brake lever. p. 94) – Adjust the basic position of the shift lever. p. 130) –...

  • Page 35: Starting Power Of Lithium-Ion Batteries At Low Temperatures

    PREPARING FOR USE 8 Starting power of lithium-ion batteries at low temperatures Lithium-ion batteries are far lighter than lead batteries, have a low self-discharge rate, and have more starting power at tem- peratures over 15 °C (60 °F). At low temperatures, however, the starting power of lithium-ion batteries drops to below that of lead batteries.
  • Page 36 – Change the radiator cap. – Mount the air filter dust cover. Air filter dust cover (79006920000) Info Observe the fitting instructions for Husqvarna Motor- cycles accessories. M01104-01 – Mount the air filter sand cover. Air filter sand cover (79006922000)

  • Page 37: Preparing The Vehicle For Riding On Wet Sand

    – Change the radiator cap. – Mount the air filter rain cover. Air filter rain cover (79006921000) Info Observe the fitting instructions for Husqvarna Motor- cycles accessories. M01106-01 – Clean the chain. – Mount the steel sprocket.

  • Page 38: Preparing The Vehicle For Riding On Wet And Muddy Circuits

    8 PREPARING FOR USE Preparing the vehicle for riding on wet and muddy circuits – Mount the air filter rain cover. Air filter rain cover (79006921000) Info Observe the fitting instructions for Husqvarna Motor- cycles accessories. M01106-01 – Mount the steel sprocket. –...

  • Page 39: Preparing The Vehicle For Low Temperatures Or Snow

    Straighten bent radiator fins carefully. – Check the coolant level. ( p. 122) Preparing the vehicle for low temperatures or snow – Mount the air filter rain cover. Air filter rain cover (79006921000) Info Observe the fitting instructions for Husqvarna Motor- cycles accessories. M01106-01...

  • Page 40: Riding Instructions

    9 RIDING INSTRUCTIONS Checks and maintenance measures when preparing for use Info Before every trip, check the condition of the vehicle and ensure that it is safe to operate. The vehicle must be in perfect technical condition when it is being operated. –...

  • Page 41: Starting Off

    RIDING INSTRUCTIONS 9 – Take the motorcycle off side stand and secure the side stand with rubber strap – Shift the transmission into neutral. (All EU models) – Turn the emergency OFF switch to the position Condition Ambient temperature: < 10 °C (< 50 °F) –...

  • Page 42: Braking

    Danger of accidents A spongy pressure point on the front or rear brake reduces braking efficiency. – Check the brake system and do not continue riding until the problem is eliminated. (Your authorized Husqvarna Motorcycles workshop will be glad to help.) Warning Danger of accidents Moisture and dirt impair the brake system.

  • Page 43: Stopping, Parking

    RIDING INSTRUCTIONS 9 – Braking should always be completed before you go into a bend. Change down to a lower gear appropriate to your road speed. Stopping, parking Warning Risk of misappropriation People who act without authorization endanger themselves and others. –...

  • Page 44: Refueling

    In some countries and regions, the available fuel quality and cleanliness may not be sufficient. This will result in problems with the fuel system. – Refuel only with clean fuel that meets the specified standards. (Your authorized Husqvarna Motorcycles workshop will be glad to help.) Note Environmental hazard Improper handling of fuel is a danger to the environment.

  • Page 45: Adding 2-Stroke Oil

    RIDING INSTRUCTIONS 9 – Fill the fuel tank with fuel up to level Guideline 35 mm (1.38 in) Level Total fuel tank 8.5 l Super unleaded capacity, approx. (2.25 US gal) (ROZ 95/RON 95/PON 91) p. 156) 401226-10 Info Do not refuel using pre-mixed fuel. –...

  • Page 46: 10 Service Schedule

    Different service intervals may apply in your country, depending on the local operating conditions. Individual service intervals and scopes may change in the course of technical developments. The most up- to-date service schedule can always be found on Husqvarna Motorcycles Dealer.net. Your authorized Husq- varna Motorcycles dealer will be glad to advise you.

  • Page 47: Recommended Work

    ● Final check: Check the vehicle for operating safety and take a test ride. ○ ○ ● ● ● Read out the fault memory after the test ride using the Husqvarna Motorcycles diag- nostics tool. ○ ○ ● ● ●...
  • Page 48 10 SERVICE SCHEDULE Every 40 operating hours when used for motorsports Every 10 operating hours when used for motorsports Every 80 operating hours Every 40 operating hours After 20 operating hours After 10 operating hours every 12 months ● Clean the oil screen in the oil tank. ●...

  • Page 49: Tuning The Chassis 11

    The shock absorber is filled with highly compressed nitrogen. – Please follow the description provided. (Your authorized Husqvarna Motorcycles workshop will be glad to help.) Info The effect of the low-speed compression adjuster can be seen in slow to normal compression of the...

  • Page 50: Adjusting The High-Speed Compression Damping Of The Shock Absorber

    The shock absorber is filled with highly compressed nitrogen. – Please follow the description provided. (Your authorized Husqvarna Motorcycles workshop will be glad to help.) Info The effect of the high-speed compression adjuster can be seen in fast compression of the shock absorber.

  • Page 51: Adjusting The Rebound Damping Of The Shock Absorber

    Risk of injury Parts of the shock absorber will move around if the shock absorber is detached incor- rectly. The shock absorber is filled with highly compressed nitrogen. – Please follow the description provided. (Your authorized Husqvarna Motorcycles workshop will be glad to help.) – Turn adjusting screw clockwise up to the last perceptible click.

  • Page 52: Checking The Static Sag Of The Shock Absorber

    11 TUNING THE CHASSIS Finishing work – Remove the motorcycle from the lift stand. ( p. 56) 11.7 Checking the static sag of the shock absorber – Measure dimension of rear wheel unloaded. ( p. 49) – Hold the motorcycle upright with aid of an assistant. –...

  • Page 53: Adjusting The Spring Preload Of The Shock Absorber

    The shock absorber is filled with highly compressed nitrogen. – Please follow the description provided. (Your authorized Husqvarna Motorcycles workshop will be glad to help.) Info Before changing the spring preload, make a note of the present setting, e.g., by measuring the spring length.

  • Page 54: Adjusting The Riding Sag

    11 TUNING THE CHASSIS 11.10 Adjusting the riding sag Preparatory work – Raise the motorcycle with a lift stand. ( p. 56) – Remove the shock absorber. p. 66) – After removing the shock absorber, clean it thoroughly. Main work –...

  • Page 55: Adjusting The Compression Damping Of The Fork

    TUNING THE CHASSIS 11 11.12 Adjusting the compression damping of the fork Info The hydraulic compression damping determines the fork suspension behavior. – Turn white adjuster clockwise as far as it will go. Info Adjuster is located at the upper end of the left fork leg.

  • Page 56: Adjusting The Spring Preload Of The Fork

    11 TUNING THE CHASSIS Info Turn clockwise to increase the damping; turn counterclockwise to reduce damping when the shock absorber rebounds. 11.14 Adjusting the spring preload of the fork Preparatory work – Raise the motorcycle with a lift stand. ( p.

  • Page 57: Adjusting The Handlebar Position

    TUNING THE CHASSIS 11 The handlebar can be mounted in four different positions. This allows the handlebar to be mounted in the most comfortable position for the rider. 11.16 Adjusting the handlebar position Warning Danger of accidents A repaired handlebar poses a safety risk. If the handlebar is bent or straightened, the material becomes fatigued.

  • Page 58: 12 Service Work On The Chassis

    12 SERVICE WORK ON THE CHASSIS 12.1 Raising the motorcycle with a lift stand Note Danger of damage The parked vehicle can roll away or fall over. – Park the vehicle on a firm and level surface. – Raise the motorcycle at the frame underneath the engine. Lift stand (81329955100) Neither wheel is in contact with the ground.

  • Page 59: Cleaning The Dust Boots Of The Fork Legs

    SERVICE WORK ON THE CHASSIS 12 12.4 Cleaning the dust boots of the fork legs Preparatory work – Raise the motorcycle with a lift stand. ( p. 56) – Remove the fork protector. ( p. 59) Main work – Push dust boots of both fork legs downward.

  • Page 60: Installing The Fork Legs

    12 SERVICE WORK ON THE CHASSIS Main work – Remove screws and take off the clamp. – Remove the cable tie. – Remove screws and take off the brake caliper. – Allow the brake caliper and brake line to hang loosely to the side.

  • Page 61: Removing The Fork Protector

    SERVICE WORK ON THE CHASSIS 12 – Position the brake caliper, and mount and tighten screws Guideline Screw, front 25 Nm (18.4 lbf ft) ® Loctite 243™ brake caliper – Mount the cable ties. – Position the brake line, the wiring harness, and the clamp. Mount and tighten screws H03679-10 Finishing work...

  • Page 62: Removing The Lower Triple Clamp

    12 SERVICE WORK ON THE CHASSIS 12.9 Removing the lower triple clamp Preparatory work (All EU models) – Press and hold the switch-off button while the engine is idling until the engine stops. (All US models) – Press and hold the switch-off button while the engine is idling until the engine stops.

  • Page 63: Installing The Lower Triple Clamp

    SERVICE WORK ON THE CHASSIS 12 12.10 Installing the lower triple clamp Main work – Clean the bearing and sealing elements, check for damage, and grease. High viscosity grease ( p. 157) – Insert the lower triple clamp with the steering stem. Mount upper steering head bearing.
  • Page 64 12 SERVICE WORK ON THE CHASSIS – Tighten screw Guideline Screw, top steering M20x1.5 12 Nm (8.9 lbf ft) head H03687-10 – Mount and tighten screw Guideline Screw, top 17 Nm (12.5 lbf ft) ® Loctite 243™ steering stem H03688-10 –...

  • Page 65: Checking Steering Head Bearing Play

    Danger of accidents Incorrect steering head bearing play impairs the handling characteristic and damages components. – Correct incorrect steering head bearing play immediately. (Your authorized Husqvarna Motorcycles workshop will be glad to help.) Info If the vehicle is operated for a lengthy period with play in the steering head bearing, the bearings and the bearing seats in the frame can become damaged over time.

  • Page 66: Greasing The Steering Head Bearing

    12 SERVICE WORK ON THE CHASSIS Guideline Screw, top triple 17 Nm (12.5 lbf ft) clamp – Mount and tighten screw Guideline Screw, top 17 Nm (12.5 lbf ft) ® Loctite 243™ steering stem Finishing work – Check steering head bearing play. ( p.

  • Page 67: Installing Front Fender

    SERVICE WORK ON THE CHASSIS 12 Main work – Remove screws – Remove screws . Take off the front fender. H03690-10 12.15 Installing front fender Main work – Position front fender. Mount and tighten screws Guideline Remaining screws, 10 Nm (7.4 lbf ft) chassis H03690-10 Finishing work...

  • Page 68: Removing The Shock Absorber

    12 SERVICE WORK ON THE CHASSIS 12.16 Removing the shock absorber Preparatory work – Raise the motorcycle with a lift stand. ( p. 56) Main work – Remove the cable ties. – Remove screws with the washers. – Detach the frame protector in area and take it off.

  • Page 69: Installing The Shock Absorber

    SERVICE WORK ON THE CHASSIS 12 – Remove the connecting link of the chain. Info Cover the components to protect them against dam- age. – Take off the chain. H03696-10 – Remove nut and pull out the swingarm pivot. – Push the link fork back and secure it against falling over.
  • Page 70 12 SERVICE WORK ON THE CHASSIS – Mount the chain. – Connect the chain with the connecting link. Guideline The closed side of the chain joint lock must face in the direction of travel. F02306-10 (All EU models) – Join plug-in connector of the brake light switch. H03698-10 –...

  • Page 71: Removing The Seat

    SERVICE WORK ON THE CHASSIS 12 – Attach frame protector in area and position. – Mount and tighten screws with the washers. Guideline Screw, frame pro- 3 Nm (2.2 lbf ft) tector – Mount the new cable ties. F02309-10 Finishing work –...

  • Page 72: Removing The Air Filter Box Cover

    12 SERVICE WORK ON THE CHASSIS – Mount and tighten screw Guideline Remaining screws, 10 Nm (7.4 lbf ft) chassis F02310-10 Finishing work – Install the air filter box cover. ( p. 70) 12.20 Removing the air filter box cover –...

  • Page 73: Removing The Air Filter

    SERVICE WORK ON THE CHASSIS 12 12.22 Removing the air filter Note Engine damage Unfiltered intake air has a negative effect on the service life of the engine. Dust and dirt will enter the engine without an air filter. – Never start to use the vehicle without an air filter. Note Environmental hazard Hazardous substances cause environmental damage.

  • Page 74: Installing The Air Filter

    12 SERVICE WORK ON THE CHASSIS – Clean the intake flange and check it for damage and tight- ness. Finishing work – Install the air filter. p. 72) – Install the air filter box cover. ( p. 70) 12.24 Installing the air filter Main work –...

  • Page 75: Installing The Main Silencer

    SERVICE WORK ON THE CHASSIS 12 12.26 Installing the main silencer – Mount the main silencer with rubber sleeve and the spring rings. – Mount and tighten screws with the washers. Guideline Remaining screws, 10 Nm (7.4 lbf ft) chassis F02316-10 12.27 Changing the glass fiber yarn filling of the main silencer...

  • Page 76: Removing The Right Side Cover

    12 SERVICE WORK ON THE CHASSIS 12.28 Removing the right side cover Preparatory work – Remove the air filter box cover. ( p. 70) – Remove the seat. ( p. 69) Main work – Detach side cover in area , pull off sideways in area and take off toward the rear.

  • Page 77: Removing The Fuel Tank

    SERVICE WORK ON THE CHASSIS 12 12.30 Removing the fuel tank Danger Fire hazard Fuel is highly flammable. The fuel in the fuel tank expands when warm and can escape if overfilled. – Do not refuel the vehicle in the vicinity of open flames or lit cigarettes. –...

  • Page 78: Installing The Fuel Tank

    12 SERVICE WORK ON THE CHASSIS – Remove screws (All EU models) – Hang the horn and horn bracket to one side. H03705-10 – Remove screw with the rubber bushing. – Pull the fuel tank breather hose off the fuel tank lid. H03704-10 –...
  • Page 79 SERVICE WORK ON THE CHASSIS 12 Main work – Check throttle cable routing. ( p. 83) – Position the fuel tank and fit the two spoilers to the sides in front of the radiator bracket. – Make sure that no cables or throttle cables are trapped or damaged.

  • Page 80: Checking The Chain For Dirt

    12 SERVICE WORK ON THE CHASSIS 12.32 Checking the chain for dirt – Check the chain for heavy soiling. » If the chain is very dirty: – Clean the chain. ( p. 78) 400678-01 12.33 Cleaning the chain Warning Danger of accidents Lubricants on the tires reduces the road grip. –...

  • Page 81: Checking The Chain Tension

    SERVICE WORK ON THE CHASSIS 12 12.34 Checking the chain tension Warning Danger of accidents Incorrect chain tension damages components and results in accidents. If the chain is tensioned too much, the chain, engine sprocket, rear sprocket, transmission and rear wheel bearings wear more quickly. Some components may break if overloaded. If the chain is too loose, the chain may fall off the engine sprocket or the rear sprocket.

  • Page 82: Checking The Chain, Rear Sprocket, Engine Sprocket, And Chain Guide

    12 SERVICE WORK ON THE CHASSIS Main work – Loosen nut – Loosen nuts – Adjust the chain tension by turning adjusting screws left and right. Guideline Chain tension 55 … 58 mm (2.17 … 2.28 in) Turn adjusting screws on the left and right so that the markings on the left and right chain adjusters are in the same position relative to reference marks...
  • Page 83 SERVICE WORK ON THE CHASSIS 12 – Pull on the top section of the chain with the specified weight Guideline Weight, chain wear mea- 10 … 15 kg (22 … 33 lb.) surement – Measure distance of 18 chain rollers in the lower chain section.
  • Page 84 12 SERVICE WORK ON THE CHASSIS – Check the chain sliding piece for wear. » If the lower edge of the chain pins is in line with or below the chain sliding piece: – Change the chain sliding piece. – Check that the chain sliding piece is firmly seated.

  • Page 85: Checking The Frame

    – Change the frame. Info Always replace a frame that has been damaged due to a mechanical impact. Repair of the frame is not authorized by Husqvarna S01339-01 Motorcycles. 12.38 Checking the link fork – Check the link fork for damage, cracking, and deformation.

  • Page 86: Checking The Rubber Grip

    12 SERVICE WORK ON THE CHASSIS Main work – Check throttle cable routing. Both throttle cables must be routed, side by side, on the back of the handlebars, above the fuel tank bracket on the right of the frame to the throttle valve body. Both throttle cables must be secured behind the rubber strap of the fuel tank support.

  • Page 87: Adjusting The Basic Position Of The Clutch Lever

    SERVICE WORK ON THE CHASSIS 12 12.41 Adjusting the basic position of the clutch lever – Adjust the basic position of the clutch lever to your hand size by turning adjusting screw Info When the adjusting screw is turned counterclockwise, the clutch lever moves away from the handlebar.

  • Page 88: Changing The Hydraulic Clutch Fluid

    12 SERVICE WORK ON THE CHASSIS Brake fluid DOT 4 / DOT 5.1 ( p. 155) – Position cover with membrane. Mount and tighten screws. Info Clean up overflowed or spilled brake fluid immediately with water. 12.43 Changing the hydraulic clutch fluid Warning Skin irritation Brake fluid causes skin irritation.

  • Page 89: Removing The Engine Guard

    SERVICE WORK ON THE CHASSIS 12 – Fill bleeding syringe with the appropriate hydraulic fluid. Syringe (50329050000) Brake fluid DOT 4 / DOT 5.1 ( p. 155) – On the slave cylinder, remove the protection cap and bleeder screw and mount bleeding syringe H03714-10 –...

  • Page 90: 13 Brake System

    Warning Danger of accidents Worn-out brake discs reduce the braking effect. – Make sure that worn-out brake discs are replaced immediately. (Your authorized Husqvarna Motor- cycles workshop will be glad to help.) – Check the front and rear brake disc thickness at multiple...

  • Page 91: Checking The Front Brake Fluid Level

    – Make sure that brake fluid for the front and rear brake is changed in accordance with the service schedule. (Your authorized Husqvarna Motorcycles workshop will be glad to help.) – Move the brake fluid reservoir mounted on the handlebar to a horizontal position.

  • Page 92: Checking The Front Brake Linings

    Checking the front brake linings Warning Danger of accidents Worn-out brake linings reduce the braking effect. – Ensure that worn-out brake linings are replaced immediately. (Your authorized Husqvarna Motorcy- cles workshop will be glad to help.) – Check the brake linings for minimum thickness ≥...

  • Page 93: Changing The Front Brake Linings

    Danger of accidents Brake linings which have not been approved alter the braking efficiency. Not all brake linings are tested and approved for Husqvarna motorcycles. The structure and friction coefficient of the brake linings, and thus their brake power, may vary greatly from that of original brake linings.
  • Page 94 13 BRAKE SYSTEM – Move the brake reservoir mounted on the handlebar to a hori- zontal position. – Remove screws – Take off cover with membrane H03720-10 – Manually press the brake caliper toward the brake disc to push back the brake pistons. Ensure that brake fluid does not flow out of the brake fluid reservoir, if necessary extract excess.

  • Page 95: Checking The Free Travel Of The Foot Brake Lever

    BRAKE SYSTEM 13 – Add brake fluid up to level Guideline 5 mm (0.2 in) Level (brake fluid level below reservoir rim) Brake fluid DOT 4 / DOT 5.1 ( p. 155) – Position cover with membrane – Mount and tighten screws Info Clean up overflowed or spilled brake fluid immediately with water.

  • Page 96: Adjusting The Basic Position Of The Foot Brake Lever

    Warning Danger of accidents Old brake fluid reduces the braking effect. – Make sure that brake fluid for the front and rear brake is changed in accordance with the service schedule. (Your authorized Husqvarna Motorcycles workshop will be glad to help.)

  • Page 97: Adding Rear Brake Fluid

    Danger of accidents Old brake fluid reduces the braking effect. – Make sure that brake fluid for the front and rear brake is changed in accordance with the service schedule. (Your authorized Husqvarna Motorcycles workshop will be glad to help.) Note Environmental hazard Hazardous substances cause environmental damage.

  • Page 98: Checking The Brake Linings Of The Rear Brake

    Checking the brake linings of the rear brake Warning Danger of accidents Worn-out brake linings reduce the braking effect. – Ensure that worn-out brake linings are replaced immediately. (Your authorized Husqvarna Motorcy- cles workshop will be glad to help.) – Check the brake linings for minimum thickness ≥...
  • Page 99 Danger of accidents Brake linings which have not been approved alter the braking efficiency. Not all brake linings are tested and approved for Husqvarna motorcycles. The structure and friction coefficient of the brake linings, and thus their brake power, may vary greatly from that of original brake linings.
  • Page 100 13 BRAKE SYSTEM – Stand the vehicle upright. – Remove the cable tie on the frame protector. – Remove screw cap with membrane and the shim. H03726-10 – Manually press the brake caliper toward the brake disc to push back the brake piston. Ensure that brake fluid does not flow out of the brake fluid reservoir, if necessary extract excess.
  • Page 101 BRAKE SYSTEM 13 – Add brake fluid to level Brake fluid DOT 4 / DOT 5.1 ( p. 155) – Mount and tighten screw cap with membrane and the shim. Info Clean up overflowed or spilled brake fluid immediately with water. –...

  • Page 102: 14 Wheels, Tires

    14 WHEELS, TIRES 14.1 Removing the front wheel Preparatory work – Raise the motorcycle with a lift stand. ( p. 56) Main work – Manually press the brake caliper toward the brake disc to push back the brake pistons. Info Make sure that you do not press the brake caliper against the spokes when pushing back the brake pis- tons.

  • Page 103: Installing The Front Wheel

    WHEELS, TIRES 14 (JARVIS EDITION) – Remove spacer and brake disc guard H01890-10 14.2 Installing the front wheel Warning Danger of accidents Oil or grease on the brake discs reduces the braking effect. – Always keep the brake discs free of oil and grease. –...

  • Page 104: Removing The Rear Wheel

    14 WHEELS, TIRES – Jack up the front wheel into the fork, position it, and insert the wheel spindle. The brake linings are correctly positioned. – Mount and tighten screw Guideline Screw, front wheel M20x1.5 35 Nm (25.8 lbf ft) spindle –...

  • Page 105: Installing The Rear Wheel

    WHEELS, TIRES 14 Info Do not operate the foot brake lever when the rear wheel is removed. – Remove spacers H03002-10 14.4 Installing the rear wheel Warning Danger of accidents Oil or grease on the brake discs reduces the braking effect. –...

  • Page 106: Checking The Tire Condition

    Checking the tire condition Info Only mount tires approved and/or recommended by Husqvarna Motorcycles. Other tires could have a negative effect on handling characteristics. The type, condition, and pressure of the tires all have a major impact on the handling characteristic of the motorcycle.

  • Page 107: Checking Tire Pressure

    Other spokes will become looser as a result. – Check spoke tension regularly, and in particular on a new vehicle. (Your authorized Husqvarna Motorcycles workshop will be glad to help.)
  • Page 108 14 WHEELS, TIRES – Strike each spoke briefly using a screwdriver blade. Info The frequency of the sound depends on the spoke length and spoke diameter. If you hear different tone frequencies from different spokes of equal length and diameter, this is an indica- tion of different spoke tensions.

  • Page 109: Electrical System 15

    ELECTRICAL SYSTEM 15 15.1 Removing the 12-V battery Note Environmental hazard 12 V batteries contain environmentally hazardous materials. – Do not dispose of 12 V batteries as household waste. – Dispose of 12 V batteries at a collection point for used batteries. Note Environmental hazard Hazardous substances cause environmental damage.
  • Page 110 15 ELECTRICAL SYSTEM – Pull EFI control unit upward off rubber lugs and hang to the side. H03738-10 – Remove starter relay and fuse box from the battery compartment and hang to the side. H03739-10 – Detach wiring harness , disconnect relays and plug , and hang to the side.

  • Page 111: Installing The 12-V Battery

    ELECTRICAL SYSTEM 15 15.2 Installing the 12-V battery Main work – Insert the 12 V battery into the battery compartment with the terminals facing forward and secure with holding bracket 12-V battery (HJTZ5S-FP-C) ( p. 151) – Mount and tighten screw Guideline Remaining screws, 10 Nm (7.4 lbf ft)

  • Page 112: Charging The 12-V Battery

    15 ELECTRICAL SYSTEM – Connect positive cable to the 12-V battery. Guideline Screw, battery termi- 2.5 Nm (1.84 lbf ft) Info Contact disk must be mounted under screw and cable lug with the claws toward the battery terminal. – Slide positive terminal cover over the positive terminal.
  • Page 113 ELECTRICAL SYSTEM 15 Info Even if there is no load on the 12-V battery, it discharges each day. The charging level and the method of charging are very important for the service life of the 12-V battery. Rapid recharging with a high charging current shortens the service life of the battery. If the charging current or charging voltage are exceeded, the 12 V battery will be destroyed.

  • Page 114: Changing Main Fuse

    15 ELECTRICAL SYSTEM This battery charger is only suitable for lithium iron phosphate batteries. Read the accompanying fitting instructions for Husqvarna Motorcycles accessories. Info Never remove cover – Switch off the battery charger after charging and disconnect it from the 12-V battery.
  • Page 115 ELECTRICAL SYSTEM 15 – Pull starter relay from the holder. H03745-10 – Take off protection caps – Remove faulty main fuse Info A faulty fuse has a burned-out fuse wire A spare fuse is located in the starter relay. – Insert a new main fuse.

  • Page 116: Changing The Fuses Of Individual Power Consumers

    15 ELECTRICAL SYSTEM 15.5 Changing the fuses of individual power consumers Info The fuse box containing the fuses of individual power consumers is located under the seat. Preparatory work (All EU models) – Press and hold the switch-off button while the engine is idling until the engine stops.

  • Page 117: Removing The Headlight Mask With The Headlight

    ELECTRICAL SYSTEM 15 Insert a spare fuse in the fuse box so that it is avail- able if needed. – Check that the power consumer is functioning properly. – Close the fuse box cover Finishing work – Mount the seat. ( p.

  • Page 118: Installing The Headlight Mask With The Headlight

    15 ELECTRICAL SYSTEM (All US models) – Disconnect plug-in connector and take off the head- light mask together with the headlight. H03751-10 15.7 Installing the headlight mask with the headlight Main work (All EU models) – Join plug-in connectors H03750-11 (All US models) –...

  • Page 119: Changing The Headlight Bulb

    ELECTRICAL SYSTEM 15 – Secure the headlight mask with rubber straps H03749-11 Finishing work – Check the headlight setting. ( p. 118) 15.8 Changing the headlight bulb Note Damage to reflector Grease on the reflector reduces the light intensity. Grease on the bulb will evaporate due to the heat and be deposited on the reflector. –...

  • Page 120: Changing The Turn Signal Bulb (All Eu Models)

    15 ELECTRICAL SYSTEM – Check the headlight setting. ( p. 118) 15.9 Changing the turn signal bulb (All EU models) Note Damage to reflector Grease on the reflector reduces the light intensity. Grease on the bulb will evaporate due to the heat and be deposited on the reflector. –...

  • Page 121: Adjusting The Headlight Range

    ELECTRICAL SYSTEM 15 The boundary between light and dark must be exactly on the lower mark for a motorcycle with rider. » If the boundary between light and dark does not meet specifications: – Adjust the headlight range. ( p. 119) 15.11 Adjusting the headlight range Preparatory work...

  • Page 122: Diagnostics Connector

    15 ELECTRICAL SYSTEM – Using a coin, turn protection cap all the way counter- clockwise and take it off. – Remove combination instrument battery – Insert the combination instrument battery with the label fac- ing outward. Combination instrument battery (CR 2032) ( p.

  • Page 123: Cooling System 16

    COOLING SYSTEM 16 16.1 Cooling system Water pump in the engine ensures forced circulation of the coolant. The pressure resulting from the warming of the cooling system is regulated by a valve in radiator cap . This ensures that operat- ing the vehicle at the specified coolant temperature will not result in a risk of malfunctions.

  • Page 124: Checking The Coolant Level

    16 COOLING SYSTEM 16.3 Checking the coolant level Warning Danger of scalding During motorcycle operation, the coolant gets very hot and is under pressure. – Do not open the radiator, the radiator hoses or other cooling system components if the engine or the cooling system are at operating temperature.

  • Page 125: Refilling With Coolant

    COOLING SYSTEM 16 Warning Danger of poisoning Coolant is toxic and a health hazard. – Keep coolant out of the reach of children. – Do not allow coolant to come into contact with the skin, the eyes and clothing. – Consult a doctor immediately if coolant is swallowed. –...
  • Page 126 16 COOLING SYSTEM – Pour coolant in up to measurement above the radiator fins. Guideline 10 mm (0.39 in) Coolant level above the radiator fins Coolant ( p. 155) 400243-10 – Push protection cap upward over the thermostat. H03761-10 – Unplug connector –...
  • Page 127 COOLING SYSTEM 16 Finishing work – Install the engine guard. ( p. 87)

  • Page 128: 17 Tuning The Engine

    17 TUNING THE ENGINE 17.1 Checking the throttle cable play – Check the throttle grip for smooth operation. – Turn handlebar as far as possible to the right. Turn the throttle grip back and forth slightly and determine the play in throttle cable Throttle cable play 3 …...

  • Page 129: Setting The Characteristic Map Of The Throttle Response

    TUNING THE ENGINE 17 Guideline Throttle cable play 3 … 5 mm (0.12 … 0.2 in) – Unscrew adjusting screw until the smooth operation or play in the throttle cable worsens. – Turn adjusting screw approx. two turns further. – Tighten nut –...

  • Page 130: Adjusting The Idle Speed

    Warning Danger of accidents The engine may go out spontaneously if the idle speed is set too low. – Set the idle speed to the specified value. (Your authorized Husqvarna Motorcycles workshop will be glad to help.) – Run the engine until warm.

  • Page 131: Programming Ambient Pressure

    TUNING THE ENGINE 17 Info Turn clockwise to decrease the idle speed. Turn counterclockwise to increase the idle speed. Make the setting in small steps. An incorrect idle speed can have a negative impact on overall engine running. 17.5 Programming ambient pressure Danger Danger of poisoning Exhaust gases are toxic and inhaling them may result in unconsciousness and death.

  • Page 132: Adjusting The Basic Position Of The Shift Lever

    17 TUNING THE ENGINE 17.7 Adjusting the basic position of the shift lever – Remove screw with the washers and take off shift lever 401950-12 – Clean gear teeth of the shift lever and shift shaft. – Mount the shift lever on the shift shaft in the required position and engage gearing.

  • Page 133: Service Work On The Engine 18

    SERVICE WORK ON THE ENGINE 18 18.1 Changing the fuel screen Danger Fire hazard Fuel is highly flammable. The fuel in the fuel tank expands when warm and can escape if overfilled. – Do not refuel the vehicle in the vicinity of open flames or lit cigarettes. –...

  • Page 134: Checking 2-Stroke Oil Level

    18 SERVICE WORK ON THE ENGINE 18.2 Checking 2-stroke oil level Warning Engine failure The engine will not be lubricated unless there is 2-stroke oil in the oil tank. If the oil level warning light lights up, the 2-stroke oil is sufficient for the remaining tank of fuel. –...
  • Page 135 SERVICE WORK ON THE ENGINE 18 Main work – Pull EFI control unit upward off rubber lugs and hang to the side. – Remove protection cap of the diagnostics connector. F02319-10 – Put throttle grip into full throttle position and secure. F02320-10 –...

  • Page 136: Cleaning The Oil Screen In The Oil Tank

    18 SERVICE WORK ON THE ENGINE – Check whether air bubbles are visible in the hose » If air bubbles are visible: – Repeat the entire procedure until air bubbles are no longer visible. – Mount protection cap on the diagnostics connector. –...
  • Page 137 SERVICE WORK ON THE ENGINE 18 – Loosen clamps of the throttle valve body. – Disconnect plug-in connector of the rear brake light switch. – Lift the subframe slightly and secure it. Info Pay attention to intake flange – Pull throttle valve body towards the rear, out of the intake flange, and hang it to the side.

  • Page 138: Checking The Gear Oil Level

    18 SERVICE WORK ON THE ENGINE – Mount throttle valve body – Remove the locking piece and position the subframe. Info Pay attention to intake flange – Join plug-in connector of the rear brake light switch. – Position and tighten clamps of the throttle valve body.

  • Page 139: Changing The Gear Oil

    SERVICE WORK ON THE ENGINE 18 Main work – Remove gear oil level monitoring screw – Check the gear oil level. A small quantity of gear oil must run out of the drilled hole. » If no gear oil runs out: –...

  • Page 140: Adding The Gear Oil

    18 SERVICE WORK ON THE ENGINE – Remove filler plug with the O-ring, and fill up with gear oil. Gear oil 0.80 l Engine oil (15W/50) (0.85 qt.) p. 155) – Mount and tighten the filler plug together with the O-ring. Danger Danger of poisoning Exhaust gases are toxic and inhaling them may result in unconsciousness and...
  • Page 141 SERVICE WORK ON THE ENGINE 18 Danger Danger of poisoning Exhaust gases are toxic and inhaling them may result in unconsciousness and death. – Always make sure there is sufficient ventilation when running the engine. – Use effective exhaust extraction when starting or running the engine in an enclosed space.

  • Page 142: 19 Cleaning, Care

    19 CLEANING, CARE 19.1 Cleaning the motorcycle Note Material damage Components become damaged or destroyed if a pressure cleaner is used incorrectly. The high pressure forces water into the electrical components, connectors, throttle cables, and bearings, etc. Pressure which is too high causes malfunctions and destroys components. –...

  • Page 143: Checks And Maintenance Steps For Winter Operation

    CLEANING, CARE 19 – After the motorcycle has cooled down, lubricate all moving parts and pivot points. – Clean the chain. ( p. 78) – Treat bare metal (except for brake discs and the exhaust sys- tem) with a corrosion inhibitor. Preserving materials for paints, metal and rubber p.

  • Page 144: 20 Storage

    – Store the vehicle in a dry location that is not subject to large fluctuations in temperature. Info Husqvarna Motorcycles recommends raising the motorcycle. – Raise the motorcycle with a lift stand. ( p. 56) –...

  • Page 145: Preparing For Use After Storage

    STORAGE 20 Info Do not use non-porous materials since they prevent humidity from escaping, thus causing corrosion. Avoid running the engine for a short time only. Because the engine will not warm up sufficiently, the water vapor produced during combustion will condense, causing engine parts and the exhaust system to rust.

  • Page 146: 21 Troubleshooting

    Clean the connector and treat with is loose or oxydized contact spray. – Malfunction in the electronic Read out the fault memory using the fuel injection Husqvarna Motorcycles diagnostics tool. – The engine has no idle speed Spark plug defective Change the spark plug. –...
  • Page 147 Fuel screen is very dirty Change the fuel screen. p. 131) – Malfunction in the electronic Read out the fault memory using the fuel injection Husqvarna Motorcycles diagnostics tool. – Fuel supply interrupted Check the fuel tank breather. – Exhaust system leaks, Check exhaust system for damage.
  • Page 148 – Read out the fault memory using the Husqvarna Motorcycles diagnostics tool. – 12-V battery discharged The 12-V battery is not being Check charging voltage. charged by the alternator –...

  • Page 149: Technical Data 22

    TECHNICAL DATA 22 22.1 Engine 22.1.1 All TE 250i models Design 1-cylinder 2-stroke engine, water-cooled, with reed intake, exhaust control and transfer duct injection Displacement 249 cm³ (15.19 cu in) Stroke 72 mm (2.83 in) Hole 66.4 mm (2.614 in) + 0.2 + 0.008 Exhaust control - setting measurement...

  • Page 150: Engine Tightening Torques

    22 TECHNICAL DATA Piston pin bearing Needle bearing Piston Cast aluminum Piston rings 2 rectangular rings Engine lubrication Separate lubrication X distance (upper edge of piston to upper edge of 0 … 0.10 mm (0 … 0.0039 in) cylinder) Z distance (height of control flap) 49.5 mm (1.949 in) Primary transmission 26:73...
  • Page 151 TECHNICAL DATA 22 Screw, stator 6 Nm (4.4 lbf ft) ® Loctite 243™ Cap nut, water pump impeller 5 Nm (3.7 lbf ft) ® Loctite 243™ Pressure connection, cylinder 8 Nm (5.9 lbf ft) ® Loctite 2701™ Screw, alternator cover 8 Nm (5.9 lbf ft) Screw, clutch slave cylinder 10 Nm (7.4 lbf ft)

  • Page 152: Capacities

    22 TECHNICAL DATA 22.3 Capacities 22.3.1 Gear oil Gear oil 0.80 l (0.85 qt.) Engine oil (15W/50) ( p. 155) 22.3.2 Coolant Coolant 1.2 l (1.3 qt.) Coolant ( p. 155) 22.3.3 Fuel Total fuel tank capacity, approx. 8.5 l (2.25 US gal) Super unleaded (ROZ 95/RON 95/PON 91) ( p.

  • Page 153: Electrical System

    (All US models) 80/100 - 21 51M TT 110/100 - 18 64M TT Dunlop Geomax AT81F Dunlop Geomax AT81 The tires specified represent one of the possible series production tires. Additional information is available in the Service section under: www.husqvarna-motorcycles.com...

  • Page 154: Fork

    22 TECHNICAL DATA 22.7 Fork Fork article number 14.15.8T.63 Fork WP XPLOR 5548 Compression damping Comfort 18 clicks Standard 15 clicks Sport 12 clicks Rebound damping Comfort 18 clicks Standard 15 clicks Sport 12 clicks Spring preload – preload adjuster Comfort Standard Sport...

  • Page 155: Chassis Tightening Torques

    TECHNICAL DATA 22 Spring length 260 mm (10.24 in) Gas pressure 10 bar (145 psi) Static sag 37 mm (1.46 in) Riding sag 110 mm (4.33 in) Fitted length 477 mm (18.78 in) Shock absorber fluid ( p. 156) SAE 2.5 22.9 Chassis tightening torques ®...
  • Page 156 22 TECHNICAL DATA Nut, rear sprocket screw 35 Nm (25.8 lbf ft) ® Loctite 2701™ Nut, rim lock 12 Nm (8.9 lbf ft) Remaining nuts, chassis 25 Nm (18.4 lbf ft) Remaining screws, chassis 25 Nm (18.4 lbf ft) Screw, bottom triple clamp 15 Nm (11.1 lbf ft) Screw, chain sliding piece 15 Nm (11.1 lbf ft)

  • Page 157: Substances 23

    SUBSTANCES 23 Brake fluid DOT 4 / DOT 5.1 Standard/classification – Guideline – Use only brake fluid that complies with the specified standard (see specifications on the container) and that exhibits the corresponding properties. Recommended supplier Castrol – REACT PERFORMANCE DOT 4 ®...
  • Page 158 23 SUBSTANCES Recommended supplier ® MOTOREX – Cross Power 2T Fork oil (SAE 4) (48601166S1) Standard/classification – SAE ( p. 159) (SAE 4) Guideline – Use only oils that comply with the specified standards (see specifications on the container) and that exhibit the corresponding properties.

  • Page 159: Auxiliary Substances 24

    AUXILIARY SUBSTANCES 24 Air filter cleaner Recommended supplier ® MOTOREX – Racing Bio Dirt Remover Chain cleaner Recommended supplier ® MOTOREX – Chain Clean High viscosity grease Recommended supplier ® – LGHB 2 Long-life grease Recommended supplier ® MOTOREX – Bike Grease 2000 Motorcycle cleaner Recommended supplier...
  • Page 160 24 AUXILIARY SUBSTANCES Universal oil spray Recommended supplier ® MOTOREX – Joker 440 Synthetic...

  • Page 161: Standards 25

    STANDARDS 25 JASO T903 MA2 Different technical development directions required a separate specification for motorcycles – the JASO T903 MA2 standard. Earlier, engine oils from the automobile industry were used for motorcycles because there was no separate motorcycle specification. Whereas long service intervals are demanded for automobile engines, the focus for motorcycle engines is on high performance at high engine speeds.

  • Page 162: 26 Index Of Special Terms

    26 INDEX OF SPECIAL TERMS Injection in the transfer ducts Electronic fuel injection in which two injection valves in the transfer ducts of the cylinders are used On-board diagnosis Vehicle system, which monitors the specified param- eters of the vehicle electronics...

  • Page 163: List Of Abbreviations 27

    LIST OF ABBREVIATIONS 27 Art. no. Article number circa compare e.g. for example etc. et cetera i.a. inter alia number poss. possibly...

  • Page 164: 28 List Of Symbols

    Malfunction indicator lamp lights up/flashes yellow – The OBD has detected a malfunction in the vehicle electronics. Come safely to a halt, and contact an authorized Husqvarna Motor- cycles workshop. The fuel level warning lamp lights up yellow – The fuel level has reached the reserve mark.

  • Page 165: Index

    INDEX INDEX Capacity 12-V battery Coolant ......150 installing ......109 fuel .
  • Page 166 INDEX Difficult riding conditions opening ......21 high temperatures ....36 Fuel, oils, etc.
  • Page 167 INDEX Rubber grip checking ......84 Main fuse changing ......112 Safe operation .
  • Page 168 INDEX tires ......151 Throttle cable play adjusting ......126 checking .
  • Page 169 *3402407en* 3402407en 10/2019 Husqvarna Motorcycles GmbH Stallhofnerstraße 3 5230 Mattighofen Austria Photo: Mitterbauer/KISKA, www.husqvarna-motorcycles.com Husqvarna Motorcycles GmbH...

This manual is also suitable for:

Te 250i us 2020Te 300i eu 2020Te 300i us 2020Te 300i jarvis edition eu 2020F2303t7 2020F2375t7 2020 ... Show all

Table of Contents