YASKAWA J1000 Technical Manual page 258

Output Frequency is not as High as Frequency Reference ................ 151
Output Phase Loss ........................................................ 132, 135
Output Terminal Status ........................................................ 202
Output Voltage Reference ..................................................... 201
ov...................................................................... 132, 137, 142
Overcurrent ................................................................ 132, 135
Overexcitation Deceleration Gain ...................................... 136, 200
Overheat 1 (Heatsink Overheat) .............................................. 136
Overload Tolerance....................................................... 181, 182
Overtorque 1............................................................... 132, 141
Overtorque Detection 1 .................................................. 132, 137
Overvoltage................................................................ 132, 137
ov Occurs When Starting a Fan or Motor Speed Loss Occurs............ 151
P
Parameter Range Setting Error................................................ 144
Parameter Setting Range Error................................................ 132
Parameter Settings ................................................................65
PASS ....................................................................... 132, 142
Password 1....................................................................... 189
Password 2....................................................................... 189
Password Settings.................................................................72
Peak Hold Current .............................................................. 203
Peripheral Devices Affected by Drive Operation .......................... 152
PF ........................................................................... 132, 138
Phase Order Selection .......................................................... 190
Poor Speed Control Accuracy................................................. 149
Power Specifications 200 V Class Models .................................. 181
Power Specifications 400 V Class Models .................................. 182
Previous Fault ................................................................... 202
Programming Mode .....................................................62, 63, 64
Protective Covers, Reattaching ............................................... 175
Protective Covers, Removing .............................................38, 175
PWM Feedback Data Fault.................................................... 132
PWM Feedback Fault .......................................................... 134
R
RAM Fault........................................................... 131, 132, 134
Rated Frequency .......................................................... 181, 182
Rated Output Capacity (kVA) ................................................ 181
Rated Voltage ............................................................. 181, 182
REMOTE ..........................................................................66
Replacement Parts .............................................................. 186
Restart Enabled ................................................................. 195
Reverse Direction............................................................... 195
Reverse Operation Selection .................................................. 189
Reverse Run Command (2-Wire sequence) ................................. 195
rH ........................................................................... 132, 138
RTS Control Selection ......................................................... 197
Run Command/Frequency Reference Source Selection Error............ 144
Run Command at Power Up................................................... 190
Run Command Input Error .................................................... 132
Run Command Selection ................................................ 147, 189
Run Command Selection during Program................................... 189
Run Command Selection Error ............................................... 132
S
Safety Hazard Definitions .......................................................11
Safety Information................................................................11
S-Curve Characteristic at Accel End ......................................... 190
S-Curve Characteristic at Accel Start ........................................ 190
YASKAWA ELECTRIC SIEP C710606 31B YASKAWA AC Drive – J1000 Technical Manual
S-Curve Characteristic at Decel End ......................................... 190
S-Curve Characteristic at Decel Start ........................................ 190
S-Curve Characteristics ........................................................ 130
SE ........................................................................... 132, 142
Serial Communication Reference Selection................................. 194
Serial Communication Transmission Error ........................... 132, 140
Setup Mode ................................................................... 63, 67
Shielded Twisted-Pair Cables ...................................................46
Side-by-Side Setup ...............................................................28
Sinking/Sourcing Mode Switch.................................................21
Slip Compensation Gain ....................................................... 190
Slip Compensation Primary Delay Time .................................... 191
Soft Charge Circuit Fault ...................................................... 132
Soft CLA Selection ............................................................. 199
Software No. (Flash) ........................................................... 202
Software No. (ROM) ........................................................... 202
Speed Agreement Detection Level ........................................... 198
Speed Search .................................................................... 196
Stall Prevention ................................................................. 130
Stall Prevention During Deceleration ....................................51, 137
Stall Prevention Level during Acceleration ................................. 198
Stall Prevention Level during Run ........................................... 198
Stall Prevention Selection during Acceleration............................. 198
Stall Prevention Selection during Deceleration............................. 198
Stall Prevention Selection during Run ....................................... 198
Standard Connection Diagram ..................................................34
STOP Key Function Selection ................................................ 200
Stopping Method After Communication Error ............................. 197
T
Terminal A1 Bias Setting...................................................... 196
Terminal A1 Gain Setting ..................................................... 196
Terminal A1 Signal Level Selection ......................................... 196
Terminal Block Configuration ..................................................37
Terminal Board Wiring Guide ..................................................46
Terminal MA, MB and MC Function Selection (relay) ................... 195
Test Run............................................................................70
Tightening Torque ................................................................39
Timing Fault..................................................................... 131
Torque Compensation Gain ............................................. 130, 191
Torque Detection 1 (N.O.)..................................................... 195
Torque Detection 2 (N.O.)..................................................... 195
Torque Detection Level 1...................................................... 199
Torque Detection Selection 1 ................................................. 198
Torque Detection Time 1 ...................................................... 199
Torque Specifications, Single Phase 200 V Class......................39, 241
Torque Specifications, Three Phase 200 V Class ......................40, 242
Torque Specifications, Three Phase 400 V Class ......................40, 242
Transistor Input Signal ...................................................... 47, 48
U
U1-01 ................................................................. 147, 149, 201
U1-02 ............................................................................. 201
U1-03 ............................................................................. 201
U1-06 ............................................................................. 201
U1-07 ....................................................................... 147, 201
U1-09 ............................................................................. 147
U1-11 ............................................................................. 202
U1-13 ............................................................................. 202
U1-19 ............................................................................. 202
http://nicontrols.com
Index
257