YASKAWA J1000 Technical Manual page 256

Frequency (FOUT) Detection 1............................................... 195
Frequency (FOUT) Detection 2............................................... 195
Frequency Reference ........................................................... 201
Frequency Reference 1......................................................... 192
Frequency Reference 2......................................................... 192
Frequency Reference 3......................................................... 192
Frequency Reference 4......................................................... 192
Frequency Reference 5......................................................... 192
Frequency Reference 6......................................................... 192
Frequency Reference 7......................................................... 192
Frequency Reference 8......................................................... 192
Frequency Reference Hold Function Selection ............................. 192
Frequency Reference Selection ............................................... 189
Frequency Reference Selection 1............................................. 147
Frequency Reference Setting Method Selection............................ 200
Frequency Reference Upper Limit ........................................... 192
Frequency Reference Wiring....................................................46
G
General Safety Information......................................................11
Ground Fault Interrupter Activates When Drive is Running ............. 152
Ground Wiring ....................................................................41
H
H1-01 ............................................................................. 194
H1-02 ............................................................................. 194
H1-03 ............................................................................. 194
H1-04 ............................................................................. 194
H1-05 .........................................................................35, 194
H1 Multi-Function Digital Input.............................................. 194
H1 Multi-Function Digital Input Selections................................. 194
H2-01 ............................................................................. 195
H2 Multi-Function Digital Outputs .......................................... 195
H2 Multi-Function Digital Output Settings ................................. 195
H3-01 ...................................................................49, 147, 196
H3-01 Details......................................................................49
H3-13 ....................................................................... 130, 151
H3 Analog Input A1............................................................ 196
H4-01 ............................................................................. 196
H4-03 ............................................................................. 196
H4 Multi-Function Analog Output AM...................................... 196
H5-01 ............................................................................. 196
H5-02 ............................................................................. 196
H5-03 ............................................................................. 196
H5-04 ....................................................................... 134, 197
H5-05 ............................................................................. 197
H5-06 ............................................................................. 197
H5-07 ............................................................................. 197
H5-12 ............................................................................. 197
H5-13 ............................................................................. 197
H5 MEMOBUS/Modbus Communications ................................. 196
Heatsink Cooling Fan Operation Selection.................................. 199
Heatsink Overheat ........................................................ 132, 141
Heavy Duty Ratings ............................................................ 180
Hunting Prevention Gain ...................................................... 130
Hunting Prevention Gain Setting ............................................. 200
I
I/O Connections...................................................................35
IGBT Maintenance ............................................................. 202
IGBT Maintenance Setting .................................................... 201
YASKAWA ELECTRIC SIEP C710606 31B YASKAWA AC Drive – J1000 Technical Manual
Initialize Parameters............................................................ 189
Initial Operation...................................................................68
Input Current (A) ......................................................... 181, 182
Input Phase Loss .......................................................... 132, 138
Input Terminals ...................................................................66
Input Voltage Setting........................................................... 193
Inrush Prevention Circuit Fault ............................................... 139
Inrush Prevention Relay Maintenance Setting .............................. 201
Inspection .................................................................. 156, 157
Installation Environment.........................................................26
Installation Orientation...........................................................27
Installation Spacing...............................................................27
Installing Multiple Drives .......................................................27
Internal Dynamic Braking Resistor Protection ...............................51
Internal Dynamic Braking Resistor Protection Selection (ERF type) ... 199
J
Jog Frequency Reference ...................................................... 192
Jog Reference Selection........................................................ 194
Jump Frequency................................................................. 130
Jump Frequency 1 .............................................................. 192
Jump Frequency 2 .............................................................. 192
Jump Frequency Width ........................................................ 192
L
L1-01 ........................................................... 136, 137, 197, 245
L1-02 ....................................................................... 197, 245
L1-13 ............................................................................. 197
L1 Motor Protection Functions ............................................... 197
L2-01 ............................................................................. 197
L2 Momentary Power Loss.................................................... 197
L3-01 ............................................................................. 198
L3-01 through L3-06 ........................................................... 130
L3-02 ................................................................. 149, 151, 198
L3-04 ........................................................... 137, 138, 150, 198
L3-05 ............................................................................. 198
L3-06 ....................................................................... 149, 198
L3 Stall Prevention Function.................................................. 197
L4-01 ............................................................................. 198
L4 Frequency Detection ....................................................... 198
L5-01 ....................................................................... 142, 198
L5 Fault Reset ................................................................... 198
L6-01 ............................................................................. 198
L6-02 ................................................................. 137, 142, 199
L6-03 ................................................................. 137, 142, 199
L6 Overtorque Detection ...................................................... 198
L8: Hardware Protection....................................................... 199
L8-01 ....................................................................... 138, 199
L8-05 ............................................................................. 138
L8-10 ............................................................................. 199
L8-12 ....................................................................... 186, 199
L8-18 ............................................................................. 199
L8-29 ............................................................................. 186
L8-35 ............................................................................. 199
L8-38 ....................................................................... 151, 199
LED Check ...................................................................... 203
LED Operator ............................................................19, 58, 59
LF ........................................................................... 132, 135
LO/RE .....................................................................60, 66, 70
LOCAL.............................................................................66
http://nicontrols.com
Index
255