Siemens SINAMICS G150 Manual page 1834

Index
B
Basic Infeed, 1224
Control word, sequence control, 1226
Interface (control signals, actual values), 1230
Missing enable signals, line contactor control, 1229
Overview, 1225
Sequencer, 1228
Signals and monitoring functions, 1224, 1231
Status word, sequence control, 1227
Table of contents, 1224
Basic Operator Panel (BOP), 1263
Basic/extended brake control, 1111
BI, Binector Input, 18
BICO technology, 1038
Binector
Input (BI), 18
Output (BO), 18
Bit field (parameter), 29
BO, Binector Output, 18
Brake control
Basic, 1111
Extended, 1111
C
C1(x) - State commissioning device, 21
C2(x) - State commissioning drive, 21
Calculated (parameter), 22
Can be changed (parameter, C1(x), C2(x), U, T), 21
Catalogs, 1822
CDS, (Command Data Set), 24, 1218, 1219
CI, Connector Input, 18
CO, Connector Output, 18
CO/BO, Connector/Binector Output, 18
Command data sets, 1218
Communication
CANopen, 1238
Communication Board CAN 10 (CBC10), 1238
Connector
Input (CI), 18
Output (CO), 18
Control
Basic Infeed, 1224
Technology controller, 1200
Vector, 1163
Control Unit 320-2 (CU320-2)
Digital inputs, 1039
Digital inputs/outputs, 1039
Control words, 1050
Internal, 1095
Standard telegrams, 1050
Converter
Binector/connector, 1081, 1086
Connector/binector, 1079, 1082, 1084, 1087
Cxxxxx, 1271
1834
D
Data Set, 24
Command data set, CDS, 24
Drive Data Set, DDS, 24
Encoder Data Set, EDS, 24
Motor Data Set, MDS, 24
Power unit Data Set, PDS, 24
Data set, 24
Data sets, 1218
Command data set, 24
Drive data set, 24
Encoder data set, 24
Motor data set, 24
Power unit data set, 24
Data type (parameter, signal source), 23
DCBRK, 1268
DDS, (Drive Data Set), 1218, 1220
DDS, drive data set, 24
Dependency (parameter), 29
Description (parameter), 28
Digital inputs
Control Unit 320-2 (CU320-2), 1039
Terminal Board 30 (TB30), 1232
Terminal Module 31 (TM31), 1245
Digital inputs/outputs
Control Unit 320-2 (CU320-2), 1039
Terminal Module 31 (TM31), 1245
Digital outputs
Control Unit 320-2 (CU320-2), 1039
Terminal Board 30 (TB30), 1232
Terminal Module 31 (TM31), 1245
Direction limitation, 1149
Direction reversal, 1149
Directory
ASCII table, 1810
Complete table of contents, 9
Index, 1829
List of abbreviations, 1813
References, 1822
Table of contents, function diagrams, 1027
Display
Alarms, 1266
Faults, 1266
Display parameters, 17
DO, Drive Object, 18
Drive data sets, 1218
Drive object, 18
DSC (Dynamic Servo Control), 1149
E
EDS, (Encoder Data Set), 24, 1218, 1221
ENCODER, 1268
Encoder data sets, 1218
Encoder evaluation, 1159
Essential service mode (ESM), 1195
List Manual (LH2), 04/2014, A5E03263479A
SINAMICS G130/G150