Tray 6 Paper Mismatch Rap - Xerox Phaser 4620 Service Manual

03-470-00 Tray 6 Paper Mismatch RAP

03-470-00 Media size setting for Tray 6 differ from those reported by the Size Switch.
BSD-Reference: WD 13
Initial Actions
• Check media size settings for the tray from the Control Panel.
• Reset the tray side and rear guides.
• Check for obstructions blocking the Size Switch.
Procedure
Use safe handling procedures when removing the module. Refer to
is heavy.
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Cycle system power. The error message is displayed.
Y N
Complete.
Inspect the Tray 6 end guide. The end guide operates the Size Switch actuators.
Y N
Replace the Tray,
Select dC330 codes 07-620, 07-630, 07-640. The switches are operational (high/low).
Y N
Replace the Size Switch, REP 7.30.
Remove the IOT, Tray 3, 4 and 5 from the Feeder. Check the Tray 6 Upper Option Harness.
The harness is undamaged.
Y N
Replace the Upper Option Harness, REP 7.31.
Check option harness continuity through all trays. The harnesses are undamaged.
Y N
Replace damaged harnesses.
Check the IOT Lower Option Harness. The harness is undamaged.
Y N
Replace the Lower Option Harness,
Replace these components in order until the error is corrected.
1. Size Switch, PL 3.10 Item 9
2. Tray, PL 7.10 Item 23
3. Feeder Board, PL 8.30 Item 7
4. MCU Board, PL 3.10 Item 3
Revision - Xerox Internal Use Only
Phaser 4600/4620 Printer Service Manual
WARNING
GP 15. The module
WARNING
REP 10.5.
03-480-00 HCF Paper Mismatch RAP
03-480-00 Media size setting for the HCF differs from those reported by the Size Switch.
NOTE: Optional Tray numbering varies by configuration. When testing HCF components, use
the dC330 codes appropriate for the HCF's position. For example, if the configuration is 5 trays
and the 5th tray is the HCF, use Tray 5 control codes.
BSD-Reference: WD 16
Initial Actions
• Check media size settings for the HCF from the Control Panel.
• Check for obstructions blocking the media guide.
Procedure
Use safe handling procedures when removing the module. Refer to
is heavy.
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Cycle system power. The error message is displayed.
Y N
Complete.
Remove media and check operation of the length guide. The media guide moves smoothly.
Y N
Clear obstructions blocking guide movement.
Select dC330 codes dependent on HCF position. The switches are operational (high/low).
Y N
Remove the IOT, Tray 3, and Tray 4 from the HCF. Check the HCF Option Harness. The
harness is undamaged.
Y N
Replace the HCF Option Harness.
Check option harness continuity through all trays. The harnesses are undamaged.
Y N
Replace damaged connectors.
Check the IOT Lower Option Harness. The harness is undamaged.
Y N
Replace the Lower Option Harness,
Replace the Size Switch, PL 7.25 Item
Replace these components in order until the error is corrected.
1. Size Switch, PL 7.25 Item 5
2. HCF Option Connector, PL 7.25 Item 15
5/2011
2-13
WARNING
GP 15. The module
WARNING
REP 10.5.
5.
Status Indicator RAPS
03-470-00, 03-480-00