Tray 3 Paper Mismatch Rap - Xerox Phaser 4620 Service Manual

03-420-00 Tray 3 Paper Mismatch RAP

03-420-00 Media size setting for Tray 3 differ from those reported by the Size Switch.
BSD-Reference: WD 13
Initial Actions
• Check media size settings for the tray from the Control Panel.
• Reset the tray side and rear guides.
• Check for obstructions blocking the Size Switch.
Procedure
Use safe handling procedures when removing the module. Refer to
is heavy.
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Cycle system power. The error message is displayed.
Y N
Complete.
Inspect the Tray 2 end guide. The end guide operates the Size Switch actuators.
Y N
Replace the Tray,
Select dC330 codes 07-320, 07-330, 07-340. The switches are operational (high/low).
Y N
Replace the Size Switch, REP 7.30.
Remove the IOT from the Feeder. Check the Tray 3 Upper Option Harness. The harness is
undamaged.
Y N
Replace the Upper Option Connector, REP 7.31.
Check the IOT option connector. The harness is undamaged.
Y N
Replace the Lower Option Harness,
Replace these components in order until the error is corrected.
1. Size Switch, PL 3.10 Item 9
2. Tray, PL 7.10 Item 23
3. Feeder Board, PL 8.30 Item 7
4. MCU Board, PL 3.10 Item 3
Revision - Xerox Internal Use Only
Phaser 4600/4620 Printer Service Manual
WARNING
GP 15. The module
WARNING
REP 10.5.
03-430-00 Tray 4 Paper Mismatch RAP
03-430-00 Media size setting for Tray 4 differ from those reported by the Size Switch.
BSD-Reference: WD 13
Initial Actions
• Check media size settings for the tray from the Control Panel.
• Reset the tray side and rear guides.
• Check for obstructions blocking the Size Switch.
Procedure
Use safe handling procedures when removing the module. Refer to
is heavy.
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Cycle system power. The error message is displayed.
Y N
Complete.
Inspect the Tray 4 end guide. The end guide operates the Size Switch actuators.
Y N
Replace the Tray,
Select dC330 codes 07-420, 07-430, 07-440. The switches are operational (high/low).
Y N
Replace the Size Switch, REP
Remove the IOT and Tray 3 from the Feeder. Check the Tray 4 Upper Option Harness. The
harness is undamaged.
Y N
Replace the Upper Option Harness, REP 7.31.
Check option harness continuity through Trays 3 and 4. The connectors are undamaged.
Y N
Replace damaged connectors.
Check the IOT Lower Option Harness. The harness is undamaged.
Y N
Replace the Lower Option Harness,
Replace these components in order until the error is corrected.
1. Size Switch, PL 3.10 Item 9
2. Tray, PL 7.10 Item 23
3. Feeder Board, PL 8.30 Item 7
4. MCU Board, PL 3.10 Item 3
5/2011
2-11
WARNING
GP
WARNING
7.30.
REP 10.5.
Status Indicator RAPS
03-420-00, 03-430-00
15. The module