Menvier Security TS2500 Installation & Programming Manual
  1. Manuals
  2. Brands
  3. Menvier Security Manuals
  4. Security System
  5. TS2500
  6. Installation & programming manual
Menvier Security TS2500 Installation & Programming Manual

Menvier Security TS2500 Installation & Programming Manual

1040 zone intruder alarm control system
Hide thumbs Also See for TS2500:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operator's Manual, Installation & Programming Manual
1040 Zone Intruder Alarm
Control System
_
~
OPEN
Installation & Programming
TS2500
SYSTEM OPEN
17:30
01 Jan
A
1
B
4
C
7
D
ENT
Sett ing the Syst em
E n t er y ou r pa s s c o de X X X X
A
th en l ea v e th e p r o tec t e d a re a.
Unsetting the System
Part Set
B ELL TES T
B
G o di r e ct ly to t h e k e yp ad an d
en te r y ou r p as s c o d e X X X X .
Part Set
NE W CODE
Resetting
C
E n t er y ou r pa s s c o de X X X X f o ll ow e d
Part Set
ZONE O M IT
by E N T the n 3 . Te l eph o n e y o u r a l ar m
D
ENT
c o m pan y a nd fo ll o w th ei r i ns tr uc t io ns .
!
Se e U se r Ma n ua l
OPEN
Engineers menu 2
Select option :-
Manual
_
~
2
3
5
6
8
9
0
ESC
1
2
3
W ALK TEST
RE SET
4
5
6
CHIME
24 Hr OMIT
7
8
9
SILENT
0
ESC
FULL S ET
_
_
~
~
_
_
~
~
Engineers menu 2
Select option :-

Advertisement

Table of Contents
loading

Related Manuals for Menvier Security TS2500

Summary of Contents for Menvier Security TS2500

  • Page 1 TS2500 1040 Zone Intruder Alarm Control System SYSTEM OPEN 17:30 01 Jan Sett ing the Syst em E n t er y ou r pa s s c o de X X X X th en l ea v e th e p r o tec t e d a re a.

  • Page 2: Table Of Contents

    Other Devices ......3 TS2500 Control Panel ..... . . 14 Printer .
  • Page 3 Output Modules ......28 Change Passcode ......54 Control Panel Connections.
  • Page 4 Modem Password......74 User Types ......85 Modem Site No.

  • Page 5: System Overview

    TS2500 Installation Manual System Overview System Overview System Architecture 2 Outputs 2 Outputs 2 Outputs Wiring Option 1 XNode Printer Data XNode XNode XNode Networks Speaker Remote Remote Remote CPA6.OM 8 Zones 8 Zones 8 Zones TS2500 Aux 12V The XNode is capable of driving...

  • Page 6: Introduction

    The directly wired to the network. The XNode also provides TS2500 system can be expanded up to 1040 zones. The the facility to connect up to 4 remote keypads giving a system is capable of “up” and “down” line loading, system total of 512 remote keypads.

  • Page 7: Xnode

    TS2500 Installation Manual System Overview XNode Technical Specifications The XNode provides eight programmable detection Control Panel circuits, two programmable outputs (one switched +ve and one switched -ve) and a loudspeaker output for Part No: TS2500 driving a 16 Ohm loudspeaker. Each XNode can also Supply 230V ±10% 50Hz...

  • Page 8: Led Remote Keypad

    TS2500 Installation Manual System Overview LED Remote Keypad TS900 Node Part No: NETLED Part No: TS900.NODE Display: 4 character seven segment Current: 60mA (normal) 60mA (alarm) Current: 60mA (normal) 70mA (alarm) Zones: Zones: Outputs: A = Switched +ve @100mA B = Switched -ve @100mA...

  • Page 9: System Design

    System Wiring Calculating Voltage Drop In order for the system work correctly the voltage at The TS2500 system uses standard 7/0.2 un-screened each device must NOT drop below 10.5V even when alarm cable to inter-connect devices within the system. running on the standby battery. Standard 7/0.2 alarm...

  • Page 10: Voltage Drop Example 1

    System Design TS2500 Installation Manual Voltage Drop Example 1 The voltage at each Node is calculated as follows: Example 1 in the figure below shows two Nodes The total current being drawn at the first Node = connected to the control panel, the first Node is 20 180mA + 180mA +180mA = 540mA.

  • Page 11: Reducing Voltage Drop - Method 1

    TS2500 Installation Manual System Design Method 1 Control Panel Node 1 Node 2 Node 3 I = 540 mA I = 360 mA I = 180 mA A (+) Node = 60mA Node = 60mA Node = 60mA B (-)

  • Page 12: Screened Cable

    System Design TS2500 Installation Manual Method 1 Control Panel Node 5 Node 3 Node 4 Node 1 Node 2 I = 720 mA I = 540 mA I = 360 mA I = 180 mA A (+) Node = 60mA...

  • Page 13: Wiring Remote Keypads To An Xnode

    TS2500 Installation Manual System Design 1 Km (Max.) 100 metres 100 metres 100 metres 100 metres Control Panel XNode XNode XNode XNode XNode I/D=1 I/D=2 I/D=3 I/D=4 I/D=16 XNodes 4-Core Data 5 to 16 Network Daisy-chained Connections 1 Km (Max.)

  • Page 14: Wiring A Loudspeaker To An Xnode

    System Design TS2500 Installation Manual TS900 Node Wiring TS900 Nodes require a 4 core cable for interconnection, XNode and up to 5 may be connected in a “daisy-chain” or “star” configuration to any one network. The distance between each Node must not exceed 100 metres and...

  • Page 15: Remote Keypads And Ts700.Lecs

    TS2500 Installation Manual System Design 500 meters (Max.) 100 metres 100 metres 100 metres 100 metres 100 metres I/D=1 I/D=2 I/D=3 I/D=4 I/D=5 Control Panel TS900 TS900 TS900 TS900 TS900 Node Node Node Node Node 4 Core 4 Core 4 Core...

  • Page 16: Tslec8

    System Design TS2500 Installation Manual 100 Metres (Max.) I/D=1 I/D=2 I/D=3 I/D=4 I/D=ENG Remote Remote Remote Remote Remote Keypad Keypad Keypad Keypad Keypad Spare Core or LEC or LEC or LEC or LEC or LEC A B C D E...

  • Page 17: External Sounders

    TS2500 Installation Manual System Design External Sounders Output Modules The control panel has one external sounder output to An output module (CPA6.OM) provides eight switched drive standard SAB or SCB modules, additional external -ve outputs @ 100mA, which can be used to drive LED’s sounders can be driven from Nodes using a relay or relays.

  • Page 18: System Installation

    Remove the back box, drill and plug the holes. Fused Terminal Mains Block 200mA Transformer Spade connection for earth lead to front cover Mains Cable Entry Printed Circuit Board (PCB) Battery Position Figure 8. TS2500 Control Panel Layout...

  • Page 19: Mains Connection

    TS2500 Installation Manual System Installation Mains Connection Battery Connections The mains supply is connected to a 3 way “Euro Type” A single 17Ah battery or two 7Ah batteries can be fused terminal block,which is fitted with a 315mA fuse. installed inside the control panel to provide continuous system operation in the event of a mains failure.

  • Page 20: Main Pcb Layout

    System Installation TS2500 Installation Manual Main PCB Layout OUTPUT MODULE PRINTER FACTORY SYSTEM POWER HEARTBEAT RESTART LEARN LED 3 LED 1 COMMS PORT Figure 11. Main PCB Layout...

  • Page 21: Connection Terminals, Plugs & Indicators

    TS2500 Installation Manual System Installation Connection Terminals, Plugs & Indicators be used if the device is fitted inside the control panel housing. The main PCB has the following connectors etc. Digicom Outputs 1 to 8 Networks 1-8 These are programmable outputs and are...
  • Page 22 If these pins are shorted whilst the system is Two removable memory devices that store the powered, the control panel will re-learn all devices operating software for the TS2500 system. on all eight networks. If after a system learn the System Current Measurement (V)

  • Page 23: Remote Keypads

    TS2500 Installation Manual System Installation ‘ Remote Keypads Loudspeaker Output. This terminal can be connected to a single 16 Ω Four types of remote keypads are available: Loudspeaker (NETLCD only). NETLCD Remote Keypad ’ Network Connections & O/P. The NETLCD remote keypad has a 32 character back-lit Terminals A to E are used to connect the remote Liquid Crystal Display (LCD).

  • Page 24: Installing A Remote Keypad On The Xnode

    System Installation TS2500 Installation Manual Installing a Remote Keypad on the XNode Installing a Keypad on to the Network Separate the cover and base by using a flat blade Separate the cover and base by using a flat blade screwdriver to gently prise the two halves apart.
  • Page 25 TS2500 Installation Manual System Installation Extension Zone enable Output module speaker selector connector Auxiliary 12V (for detectors) AUX 12V SPEAKER OUTPUT MODULE Programmable Speaker detection volume control circuits E - H REMOTE ZONE SPEAKER ENABLE VOLUME I/D selector Tamper switch...

  • Page 26: Installing An Xnode

    I/D. keypads as required. Finally clip the Node cover onto the base being Set JP4 to the TS2500 position. careful not to trap any cables or to obstruct the Finally clip the XNode cover onto the base being tamper switch.
  • Page 27 TS2500 Installation Manual System Installation Fit jumper-link to disable Tamper switch tamper switch JP2 FITTED = NO TAMPER I/D selector Programmable detection NODE I/D circuits E - H Programmable detection Auxiliary 12V circuits A - D fuse (500mA) AUX 12V...

  • Page 28: Ts900Id Node

    System Installation TS2500 Installation Manual TS900 ID NODE Installing a TS900 ID NODE You can site the ID Node either inside the control panel The TS900 ID Node can be used as an alternative to the or remotely. If you site the ID Node remotely the standard TS900 or XNODE.

  • Page 29: Ts700 Lec

    TS2500 Installation Manual System Installation TS700 LEC TS700 LECs connected to the Network The TS700 LEC allows the facility to add an extra two Circuit A Circuit B Output p r o gra mmab le de te c tio n c irc uits and o ne...

  • Page 30: Detection Circuit Wiring

    System Installation TS2500 Installation Manual Detection Circuit Wiring normally closed devices and then must be programmed with the “Invert” attribute. All detection circuits may be wired as “End Of Line” (EOL) If the detection circuit is not used links can be fitted or ”Double Pole"...

  • Page 31: Installing An External Sounder From A Node

    TS2500 Installation Manual System Installation Typical Control Panel External Sounder 1 x 16 Ohm Loudspeaker H/O + 12V + H/O - Tamper In TR - Tamper Out STB - Strobe +ve TRG - Strobe -ve Trigger -ve Figure 21. External Sounder Connections...

  • Page 32: Dc54/Dc58 Plug-On Digicoms

    System Installation TS2500 Installation Manual DC58M Plug-on Digi-modem A plug-on digi-modem DC58M can be fitted inside the CONTROL 3GSTU control panel to allow remote interrogation and PANEL programming via a personal computer (PC). It will also function as a standard digicom (if required). The unit...

  • Page 33: Connecting A Printer

    DCI Connect to JP1 Connecting a Printer PRINTER The TS2500 supports two type of printers, the CPA6 DATAC or RS232 printer printer (no longer available) and any standard RS232 printer. When using an RS232 printer a DCI/MPA printer adaptor will be required. Menvier Security supply a DATAC printer kit which consists of a portable RS232 Figure 28.

  • Page 34: Monitoring A Remote Power Supply

    Program As:- Monitoring a Remote Power Supply Supply Custom Fail The TS2500 can be configured to monitor a 519XB Circuit 1 Battery power supply unit using a 519FM fault monitor PCB. The 519FM plugs directly onto the 519XB PCB plug labelled Fail JP1.

  • Page 35: Pre Power-Up Checks

    1.5A. Place a small screwdriver blade between the pins on the control panel PCB, marked “FACTORY The TS2500 has an overload protection RESTART". This will ensure the factory default circuit. If the power supply is overloaded, the parameters are set, see page 49 for a list of display will show: “PSU OVERLOAD ! ! !”...
  • Page 36 System Installation TS2500 Installation Manual...

  • Page 37: Engineer's Menu 1

    TS2500 Installation Manual Engineer’s Menu 1 Engineer’s Menu 1 Introduction Enter Engineer's Engineers menu 1 is the first of four engineers menus, Passcode which is selected when the engineer’s passcode is 1 2 3 4 entered. The Engineer may leave “Engineer menu 1" by pressing the [ESC] key.

  • Page 38: Panel Outputs

    Engineer’s Menu 1 TS2500 Installation Manual Panel Outputs [1-1] Digicom Channels [1-3] Outputs 1 - 4 on the control panel PCB can be The 8 plug-on digicom channels can be programmed programmed to any of the output types shown on to any of the output types shown on pages 35 - 39.

  • Page 39: Programmable Output Types

    TS2500 Installation Manual Engineer’s Menu 1 Programmable Output Types Alarm Activates when any ward is in alarm, deactivates The TS2500 output types are broken down in to four when all ward alarms have been reset. specific groups: Panic Alarm (PA) Circuit...
  • Page 40 Engineer’s Menu 1 TS2500 Installation Manual Phone Line Fault Custom o/p 5 on Activates when a line fault is detected, Activates when a combination of output deactivates when the telephone line is restored. conditions occur, see “Custom Outputs” on page...
  • Page 41 TS2500 Installation Manual Engineer’s Menu 1 PC Output 2 On Bell box tamper This output is controlled by a PC with Lineload Activates when the bell tamper is triggered, software. deactivates when the alarm is reset. PC Output 3 On...

  • Page 42: User Output Types

    Engineer’s Menu 1 TS2500 Installation Manual Custom cct 3 Ward Alarm Activates when the custom circuit 3 is triggered, Activates when the selected ward is in alarm, deactivates when custom circuit 3 is reset. deactivates when the selected ward is reset.
  • Page 43 TS2500 Installation Manual Engineer’s Menu 1 Ward Settling Ward Auto set Activates when the selected ward settling timer is Activates when the selected high security ward is running. unset, deactivates when the high security ward is set. Ward Clear Activates when the selected ward is clear of faults...

  • Page 44: Program Circuits

    Exit Term A circuit that is normally connected to a push button The TS2500 can monitor up to 1040 detection circuits, outside the protected area, which can be used to finally each circuit must be programmed in order for the set the area.

  • Page 45: Circuit Wards

    Activity Circuits with this attribute are monitored so that when The TS2500 has sixteen wards which are labelled A to P, they activate the circuit activation is stored. When the each circuit can be assigned into one or more wards.

  • Page 46: System Timers

    Engineer’s Menu 1 TS2500 Installation Manual System Timers [1-5] Abort delay This timer sets the period in which the alarm signal may There are 103 programmable system timers which are be aborted following an alarm condition. When an listed below.
  • Page 47 TS2500 Installation Manual Engineer’s Menu 1 Global bell dly. Payment time If the system is fully set and the Global/Ward Bell The installation company may use this timer to prevent configuration option (23) is set to “Global” the system will the users from setting the system.

  • Page 48: Setting Modes

    Engineer’s Menu 1 TS2500 Installation Manual Setting Modes [1-6] Do System Print [1-7] Each ward A to P can be programmed to set by one of The system print option is broken down into sections so the following modes: that the engineer may print only the relevant details. The...

  • Page 49: System Options

    TS2500 Installation Manual Engineer’s Menu 1 Reset algorithm Engineers menu 1 Do system print When a ward is programmed for “Engineer Reset” the requirement to send an engineer to site can be overridden by the user by using the “Remote Reset”...

  • Page 50: Configuration

    Engineer’s Menu 1 TS2500 Installation Manual Configuration [1-9] Unset ward first (Default) When the system is part set and a passcode is There are 35 configuration options as follows: entered the “0=UNSET WARDS” option will be displayed first. Bell Is an SAB (Default)
  • Page 51 TS2500 Installation Manual Engineer’s Menu 1 Modem on Com1 (Default) 24hr Omit Global (Default) The panel comms port (JP8) is used for the Any 24hr circuit or group can be omitted from any modem. remote keypad. Printer on Com1 24hr Omit Local The panel comms port (JP8) is used for the printer.
  • Page 52 If this is the case then the only way of returning the system to its factory default setting is by returning the control panel PCB to Menvier Security. Unshunt. no exit (Default) The use of a shunt code to reinstated a selected group of circuits will not initiate the exit procedure.

  • Page 53: Location Text

    TS2500 Installation Manual Engineer’s Menu 1 Location Text [1-A] Section Option Default This option allows the engineer to view the following:- Reset Message CALL ENGINEER TO RESET SYSTEM Panel Location Text Location Text PANEL LOCATION This option displays the panel location text which is TEXT NOT SETUP programmed in “Engineers menu 3", see “Custom Text...
  • Page 54 Engineer’s Menu 1 TS2500 Installation Manual Section Option Default Section Option Default Activity flt ok Monitor cct time 060 Seconds Latching 24hr Beam pair time 010 Seconds Access code only Battery test dur 030 Seconds Answer anytime Answer ring time...

  • Page 55: Goto User Menu 1

    TS2500 Installation Manual Engineer’s Menu 1 Log Off Engineer [1-C] Section Option Default Selecting this option will log off all engineers and return Relearn required Not assigned the system to the “SYSTEM OPEN” condition. Re-arms apply to Ward A Hi Security ward...
  • Page 56 Engineer’s Menu 1 TS2500 Installation Manual...

  • Page 57: Engineer's Menu 2

    TS2500 Installation Manual Engineer’s Menu 2 Engineer’s Menu 2 Introduction Engineers menu 1 Select Option :- Engineers menu 2 is selected by pressing the [ENT] whilst Engineers menu 1 is selected. Each menu option can be selected by pressing the relevant “hot-key” or you...

  • Page 58: View Circuits

    Engineer’s Menu 2 TS2500 Installation Manual View Circuits [2-1] Set System Date [2-3] Each detection circuit may be viewed to ascertain its The system date is displayed in a day/date/month status. The circuit status conditions and resistance are format on LCD remote keypads. it is also used to provide shown below: date stamps for events in the system log.

  • Page 59: Alter Chime Circuits

    TS2500 Installation Manual Engineer’s Menu 2 Alter Chime Circuits [2-5] Engineers menu 2 Alter 24hr group This option allows an alternative method of programming circuits as “chime”. Three types of chime tones are available: Wards 24hr group Wards A,B,*,*,.,.,.,. Chime 1 Generates a single two-tone chime sound.

  • Page 60: Alter Circuit Wards

    Engineer’s Menu 2 TS2500 Installation Manual Alter Circuit Wards [2-8] View System Log [2-9] Normally the engineer will assign circuits to wards when The engineer can use this option to view the system log. using the “Program circuits” option in Engineers menu 1,...

  • Page 61: Log Event Codes

    TS2500 Installation Manual Engineer’s Menu 2 Log Event Codes Event Description —- NO EVENT —- No event #### ACTIVATED Monitored circuit activated #,## LEC LOST Network #, device No. ## is a LEC that has been removed ### LEC or REM’S The number of LEC or REM’s logged on to system after a re-learn...
  • Page 62 Engineer’s Menu 2 TS2500 Installation Manual Event Description CODE TAMPER Keypad locked out for 5 minutes due to invalid entry of passcode COMMS FAILED Plug-on digicom failed to communicate with ARC COMMS SUCCESSFUL Plug-on digicom communicated successfully with the ARC...
  • Page 63 TS2500 Installation Manual Engineer’s Menu 2 Event Description PHONE LINE FAULT Telephone line fault detected QUICK SET KEY # Quick set key A, B or C activated Q.SET ABORTED Quick set key aborted REARM ON WARDS:- Wards:- A - P re-armed...

  • Page 64: Start Call Back

    Engineer’s Menu 2 TS2500 Installation Manual Start Call Back [2-A] Set BST/GMT Date [2-C] If the the system is fitted with a DC58M digi-modem, it is This option allows the engineer to specify the dates at possible for the installation engineer to initiate an which BST starts and ends.

  • Page 65: Engineers Menu 3

    TS2500 Installation Manual Engineers Menu 3 Engineers Menu 3 Introduction Engineers menu 2 Select Option :- Engineers menu 3 is selected by pressing the [ENT] whilst Engineers menu 2 is selected. Each menu option can be selected by pressing the relevant “Hotkey” or you...

  • Page 66: Time Switches

    [3-1] Part Set Groups [3-2] The TS2500 has three programmable time switches. This option allows the engineer to define up to 10 Each time switch can be programmed with up to three part-set groups. Each group can be programmed so separate on/off times and made to operate on any day that it sets any combination of wards.

  • Page 67: Use On-Line Pad

    If the system is fitted with a DC58M digi-modem, you This option allows the engineer to assign a name (8 can use this option to connect to another TS2500 or characters) to each user. When using the view log TS790/900 (providing the remote system also has a option you can press the [B] key to alternate between modem fitted).

  • Page 68: Circuit Text

    Engineers Menu 3 TS2500 Installation Manual Circuit Text [3-6] Delete The delete option erases the circuit text for the Each detection circuit can have up to 16 characters of selected circuit. text assigned to it. Paste When you have selected the circuit that you require to...

  • Page 69: Circuit Text Library

    TS2500 Installation Manual Engineers Menu 3 Circuit Text Library Phrase Phrase Phrase Phrase Above Church Loading bay PIR Refectory Access Classroom Lobby Research Accountant Cleaners Lounge Restaurant Accounts Collection Lounge PIR Roller Admin office Communicator Lounge window Room Animal Computer...

  • Page 70: Custom Text Menu

    Engineers Menu 3 TS2500 Installation Manual Custom Text Menu [3-7] Aux. Tamper 1/2 The control panel has two auxiliary tamper inputs, this This menu option allows the installation engineer to edit option allows the engineer to program a 16 character the following text messages: text description for each input.

  • Page 71: Equipment O/P's

    TS2500 Installation Manual Engineers Menu 3 Equipment O/P’s [3-8] This option allows the engineer to program the two outputs on each node and the single output on each remote keypad or LEC. Engineers menu 3 Equipment O/P's Output Device No.

  • Page 72: Built In Tests

    Built In Tests [3-9] View Circuit Resistance When this test routine is selected the resistance for each The TS2500 system has the following diagnostic routines: detection circuit may be measured, the accuracy of this measurement is ± 0.1 KOhms. Engineers menu 3...

  • Page 73: Test Node Outputs

    TS2500 Installation Manual Engineers Menu 3 Test Node outputs Test Keypad display This test routine allows the engineer to test all Node This test routine allows the engineer to test the LCD on all outputs. TS900 remote keypads. [ENT] to test :-...

  • Page 74: View Network Errors

    Engineers Menu 3 TS2500 Installation Manual View Network errors [ENT] to do This test routine allows the engineer to view the number False setting of data transmission errors for each network. [ENT] to view :- Network errors False set wards:...

  • Page 75: Custom Outputs

    TS2500 Installation Manual Engineers Menu 3 Custom Outputs [3-A] Custom Output - Example 3 This example shows how to use both the “AND” and “OR” This option allows the engineer to program the eight functions so that the “Custom Output” activates when custom outputs type.

  • Page 76: Custom Circuits

    Engineers Menu 3 TS2500 Installation Manual Engineers menu 3 Custom outputs [ENT] to edit :- Custom o/p 1,x Press to select the custom output to edit Custom o/p 3,1 0001 Alarm Press to select the switch number to edit output type...

  • Page 77: Digi/Modem Options

    TS2500 Installation Manual Engineers Menu 3 Trig Custom o/p Digi/Modem Options [3-C] A custom circuit with the “Trig Custom o/p” attribute will This option allows the engineer to program the plug-on activate the relevant “Custom Circuit” output type, e.g. digicom or digi-modem.

  • Page 78: Modem Password

    Engineers Menu 3 TS2500 Installation Manual [ENT] to edit :- [ENT] to edit :- Modem site no. Call back no.1 [ to edit [ENT] to edit :- Call back no.2 Site No. 2500 |Modem site no. [ENT] to edit :- Cursor Call back no.3...
  • Page 79 TS2500 Installation Manual Engineers Menu 3 Engineers menu 3 Digi/Modem opt. SET/DAY CHANNELS Extended Format [ENT] to edit :- Call back no.1 * * * 4 * * * * Will NOT Report Select Set/Day (Open/Close) Select point ID reporting mode:...

  • Page 80: Digi Baud Rate

    Engineers Menu 3 TS2500 Installation Manual Digi Baud rate This option allows the engineer to set the baud rate for [ENT] to edit :- Internal digi the plug-on digicom. For the DC54/58/58M this MUST be set at 300 baud. [ to edit Channel No.

  • Page 81: Engineers Menu 4

    TS2500 Installation Manual Engineers Menu 4 Engineers Menu 4 Introduction Engineers menu 3 Select Option :- Engineers menu 4 is selected by pressing the [ENT] whilst Engineers menu 3 is selected. Each menu option can be selected by pressing the relevant “hotkey” or you can...

  • Page 82: Auto-Set Timers

    Engineers Menu 4 TS2500 Installation Manual Auto-set Timers [4-1] The TS2500 has three auto-set timers, each timer has the following options: Set times 1, 2 & 3 Each timer has three Independent setting times. Unset time 1, 2 & 3 Each timer has three Independent unsetting times.

  • Page 83: Network Equipment Wards

    TS2500 Installation Manual Engineers Menu 4 Network Equipment Wards [4-2] Engineers menu 4 Net Equ. wards This option allows the engineer to assign remote keypads, XNodes and Nodes to wards.This will ensure that lid tamper alarms from devices on the network...

  • Page 84: Equipment Wards

    Engineers Menu 4 TS2500 Installation Manual Equipment Wards [4-3] If “No Set-AC Off” is enabled (see configuration) users assigned to the same wards as the “Mains This option allows the engineer to assign the following Power Off” cannot set their wards until the mains options to wards.

  • Page 85: Hi Security Ward

    TS2500 Installation Manual Engineers Menu 4 Hi Security ward Engineers menu 4 Equipment wards If a ward is selected as “High Security” the ward will always attempt to stay in a set condition. If the ward is unset by a user the remote keypads display "HI SECURE Panel tamper UNSET"...

  • Page 86: Log Search Keys

    [4-6] This option allows the engineer to configure the nine log The TS2500 alarm system has 50 shunt groups each search keys. When viewing the event log you would group can have up to 4 circuits assigned to it. Each normally use the [A] and [C] keys to scroll backwards circuit must have the “Shuntable”...

  • Page 87: Om Configuration

    TS2500 Installation Manual Engineers Menu 4 OM Configuration [4-7] Edit Quick Keys [4-9] This option allows the engineer to define which ward This options allows the engineer to configure the [A], [B] and circuit status information is sent to the control panel and [C] keys on the remote keypads to perform set output module port.

  • Page 88: Code Lock Times

    Engineers Menu 4 TS2500 Installation Manual Engineers menu 4 Code lock times Codelock group 1 Select option :- = Codelock group 1 = Codelock group 2 = Codelock group 3 = Off time 1 = 1st operates on 0 = Manually...

  • Page 89: User Types

    Text Editing Keys Setup New Users When programming any text the keys on the keypad The TS2500 allows up to 199 users to operate the alarm function as shown below: system, each user is assigned a user type, passcode and ward access. User 001 is the master user which has a default setting of 5678.

  • Page 90: User Wards

    Appendices TS2500 Installation Manual Duress Code Customising Users This user type operates in the same way as a standard Access to user menus is initially defined by the user type, global user, but when the passcode is used a silent e.g.
  • Page 91 TS2500 Installation Manual Appendices Enter master user (5678) then [ User menu 1 Select option :- User menu 2 Select option :- User menu 2 Setup new users Define new users Next available user User no. 002 to view total number of users Enter user No.

  • Page 92: Engineer's Quick Reference

    Appendices TS2500 Installation Manual Engineer's Quick Reference Engineers Menu 1 Hotkey Options Page Hotkey Options Page Program Panel Outputs System Print-out 1 = Panel Output 1 (relay) 0 = Custom text 8 = Code locks 2 = Panel Output 2 (-ve)

  • Page 93: Engineers Menu 2

    TS2500 Installation Manual Appendices Engineers Menu 2 Engineers Menu 3 Goto User Menu 1 Hotkey Option Page 1 = Bell Test 6 = 24hr Omit 2 = Walk Test 7 = Omit Circuits Program Time Switches 3 = Remote Reset...
  • Page 94 Appendices TS2500 Installation Manual Engineers Menu 4 Engineers Wards Hotkey Option Page Auto-set Timers A = Timer 1 1 = Set Time 1 B = Timer 2 2 = Set Time 2 C = Timer 3 3 = Set Time 3...
  • Page 95 TS2500 Installation Manual Index Beam Pair Programming via panel 74 Index Attribute 41 Resetting 76 Delay timer 42 Wiring details 28 Bell DC58M Digi modem Assigning to wards 81 Answer call options 48 Fuse 18 General 13 24hr Circuits Global / ward option 47...
  • Page 96 Index TS2500 Installation Manual Alarms 80 Monitored Attribute 41 Tampers 80 Goto user menu 1 51 Engineer Tests Engineer test attribute 41 Network Equipment Wards 79 Test routines 68 Networks Engineers Menus Heartbeat LED 18 Connections 17 Menu 1 33...
  • Page 97 TS2500 Installation Manual Index Power-Up Service Timer 43 Checks 31 Setting View exit errors option 48 Sequence 31 Global / local option 47 Voltage Printer Modes 44 Measuring at control panel 68 Shunt CPA6 29 Measuring at XNode 69 DATAC 29...
  • Page 98 Cooper Security Ltd. Security House, Xerox Business Park, Mitcheldean, Gloucestershire, GL17 0SZ. England Product Support Tel: +44 (0)1594 545556 Between 09:00 and 17:00, Monday to Friday. Product Support Fax: +44 (0)1594 545401. w ww.coopersecurity.co.uk Part No. 496497 Issue 1...

Table of Contents