Program Mode; Parameter Groups - Omron SYSDRIVE 3G3FV User Manual

Preparing for Operation
3-5

Program Mode

The Inverter parameters can be set in program mode. The parameters which can be dis-
played and changed depend on the access level and control mode that are being used.
Refer to the following table to determine if a parameter can be changed.
S Parameter Groups
An "OK" in the control mode column indicates that the parameter can be changed in that control mode.
G oup Group Function u c o
Application ca o
b1 Sequence
b2 DC Braking
b3 Speed Search
b4 Delay Timers
b5 PID Control
b6 Reference Hold
b7 Droop Control
b8 Energy Saving
b9 Zero Servo
Tuning u g
C1 Accel/Decel
C2 S-Curve Acc/Dec
C3 Motor-Slip Comp
C4 Torque Comp
C5 ASR Tuning
C6 Carrier Freq
C7 Hunting Prev
C8 Factory Tuning
Reference e e e ce
d1 Preset Reference
d2 Reference Limits
d3 Jump Frequencies
d4 Sequence
d5 Torque Control
Motor o o
E1 V/f Pattern
E2 Motor Setup
E3 Control Method 2
E4 V/f Pattern 2
E5 Motor Setup 2
O Options o s
F1 PG Option Setup
F2 AI-14 Setup
F3 DI-08, 16 Setup
F4 AO-08, 12 Setup
F5 Not used (DO-02)
F6 Not used (DO-08)
F7 PO-36F Setup
F8 SI-F/G Setup
F9 CP-916 Setup
Comments Co e s
Settings such as the reference input method
DC braking function settings
Speed search function settings
Timer function settings
PID control settings
Accel/deceleration time dwell function settings
Droop control (speed drop) settings
Terminal input energy-saving control settings
Stop in the position loop
Acceleration/deceleration time settings
S-curve characteristics for accel/decel times
Slip compensation function settings
Torque compensation function settings
Speed control loop parameter settings
Carrier frequency settings
Hunting prevention function for V/f control
Adjustment for open-loop vector control
Operator frequency reference settings
Frequency upper and lower limit settings
Prohibited frequency settings
Hold for analog frequency reference
Parameter settings for torque control
Sets the motor's V/f characteristics.
Sets the motor parameters.
Sets the control method of motor 2.
Sets the V/f pattern of motor 2.
Motor setup for motor 2.
Parameter settings for a PG Card
Parameter settings for an Analog Reference Card
Parameter settings for a Digital Reference Card
Parameter settings for an Analog Monitor Card
Not Used. (Do not change these settings.) o Used ( o o c a ge ese se
Parameter settings for a Pulse Monitor Card.
SYSMAC BUS Interface card setup.
CompoBus/D (DeviceNet) communications card
setup.
Control mode
V/f V/f
w/PG
OK OK
OK OK
OK OK
OK OK
OK OK
OK OK
--- ---
OK OK
--- ---
OK OK
OK OK
OK OK
OK OK
--- OK
OK OK
OK OK
--- ---
OK OK
OK OK
OK OK
OK OK
--- ---
OK OK
OK OK
OK OK
OK OK
OK OK
--- OK
OK OK
OK OK
OK OK
gs ) --- ---
OK OK
OK OK
OK OK
Chapter 3
Open-loop Flux
Vector Vector
OK OK
OK OK
OK OK
OK OK
OK OK
OK OK
--- OK
--- ---
--- OK
OK OK
OK OK
OK OK
OK ---
--- OK
OK OK
--- ---
OK ---
OK OK
OK OK
OK OK
OK OK
--- OK
OK OK
OK OK
OK OK
OK OK
OK OK
--- OK
OK OK
OK OK
OK OK
--- ---
OK OK
OK OK
OK OK
3-25