Common Functions; Summary Of Common Control Functions - Omron SYSDRIVE 3G3FV User Manual

Advanced Operation
6-5

Common Functions

This section summarizes the functions that can be used in common among the various
modes, and provides detailed explanations of their operations.

6-5-1 Summary of Common Control Functions

An "OK" in the control mode column indicates that the parameter can be changed in that control mode.
The functions that can be used in common are marked with a "S " and described in more detail later in
this section.
G oup Group Function u c o
Application ca o
b1 Sequence
b2 DC Braking
b3 Speed Search
b4 Delay Timers
b5 PID Control
b6 Reference Hold
b7 Droop Control
b8 Energy Saving
b9 Zero Servo
Tuning u g
C1 Accel/Decel
C2 S-Curve Acc/Dec
C3 Motor-Slip Comp
C4 Torque Comp
C5 ASR Tuning
C6 Carrier Freq
C7 Hunting Prev
C8 Factory Tuning
Reference e e e ce
d1 Preset Reference
d2 Reference Limits
d3 Jump Frequencies
d4 Sequence
d5 Torque Control
Motor o o E1 V/f Pattern
E2 Motor Setup
E3 Control Method 2
E4 V/f Pattern 2
E5 Motor Setup 2
O Options o s F1 PG Option Setup
F2 AI-14 Setup
F3 DI-08, 16 Setup
F4 AO-08, 12 Setup
F5 DO-02 Setup
F6 DO-08 Setup
F7 PO-36F Setup
F8 SI-F/G Setup
F9 CP-916 Setup
6-40
Comments Co
S Settings such as the reference input method
S DC braking function settings
S Speed search function settings
S Timer function settings
S PID control settings
S Accel/deceleration time dwell function settings
Droop control settings
Multi-function input: Sets energy-saving control by ener-
gy saving reference.
Zero servo settings
Acceleration/deceleration time settings
S S-curve characteristics for accel/decel times
S Slip compensation function settings
S Torque compensation function settings
Speed control tuning
S Carrier frequency settings
Hunting prevention settings
Adjustment for open-loop vector control
Frequency reference settings (when using Operator)
S Frequency upper and lower limit settings
S Prohibited frequency settings
S Up/Down, Accel/Decel stop hold frequency setting
Torque control settings and tuning
S Motor settings
S
o o se gs
S Control mode settings for second motor
S S Parameter settings for second motor
a a e e se gs o seco d
Parameter settings for a PG Speed Control Card
S Parameter settings for an Analog Command Card
S Parameter settings for a Digital Command Card
S Parameter settings for an Analog Monitor Card
Not Used. (Do not change these settings.) o Used ( o o c a ge
S Parameter settings for a Pulse Monitor Card
S Parameter settings for a SYSMAC BUS Interface
Card.
S Parameter settings for a CompoBus/D Communica-
tions Card.
e s
o o
ese se gs )
Chapter 6
Control mode
V/f V/f Open-loop Flux
w/PG Vector Vector
OK OK OK OK
OK OK OK OK
OK OK OK OK
OK OK OK OK
OK OK OK OK
OK OK OK OK
--- --- --- OK
OK OK --- ---
--- --- --- OK
OK OK OK OK
OK OK OK OK
OK OK OK OK
OK OK OK ---
--- OK --- OK
OK OK OK OK
OK OK --- ---
--- --- OK ---
OK OK OK OK
OK OK OK OK
OK OK OK OK
OK OK OK OK
--- --- --- OK
OK OK OK OK
OK OK OK OK
OK OK OK OK
OK OK OK OK
OK OK OK OK
--- OK --- OK
OK OK OK OK
OK OK OK OK
OK OK OK OK
--- --- --- ---
OK OK OK OK
OK OK OK OK
OK OK OK OK