Omron E5EK - MANUAL 2 User Manual page 154

INDEX
Output assignments, 1−5 , 3−7
Output Rating and Performance, A−4
P
Panel cutout, 2−4
Parameter initialize, 5−26
PARAMETER OPERATIONS LIST, A−11
Parameter types, 1−6
Parameters, 6−10
Parameters and Menus, 1−6
PID / ON/OFF, 5−32
Platinum resistance thermometer, 7−12
Power supply, 2−7
Precautions when wiring, 2−7
Preparation, 7−7 , 7−9 , 7−10
Preparations, 7−4
Procedure, 2−3
Proportional band, 5−12
Protect Mode, 1−6 , 1−8 , 3−13 , 5−3
PV/SP , 5−7
R
Ratings, A−2
Read data assignment 1 to 16, 5−38
Registering calibration data, 1−10
Relationship with set point limiter, 4−7
Remote I/O communications, 6−3
Remote SP enable, 5−39
Remote SP input, 1−4 , 2−9
Remote SP input error, 8−5
Remote SP lower limit, 5−40
Remote SP monitor, 4−8 , 5−8
Remote SP upper limit, 5−40
Remote/Local, 5−18
Restrictions during SP ramp, 4−6
Run/Stop, 5−9
S
Sample Ladder, 6−14
Scaling, 4−7
Scaling lower limit, 5−26
Scaling upper limit, 5−26
Security, 3−13 , 5−3
Selecting modes, 1−7
Selecting parameters, 1−8
Selecting the Control Method, 4−2
Sensor input, 2−8
Set point during SP ramp, 5−8
Set point limiter, 4−5
Setting Alarm Type, 3−10
Setting and Monitoring Parameter List, A−7
Setting enabled channels, 6−8
Setting example when two E5EK−DRTs are
used, 6−7
Setting Input Specifications, 3−4
Setting Output Specifications, 3−7
Setting range and Indication range of Sensor
input, A−4
Setting reserved channels, 6−8
Setting the Communications Conditions, 6−6
Setting the LBA detection time, 4−12
Setting up, 2−2
Setting up the output unit, 2−3
Setting up the terminal covers, 2−6
Setup, 3−3
Setup Conditions, 6−14
Setup conditions, 6−8
Setup Mode, 1−6 , 1−7 , 5−24
Slave Device Protocol, A−13
SP mode, 4−7 , 5−18
SP ramp, 4−5
SP ramp set value, 5−19
SP ramp time unit, 5−19
SP setting lower limit, 5−32
SP setting upper limit, 5−32
SP tracking, 4−8
SP tracking enable, 5−41
SPECIFICATIONS, A−2
Specifications, A−5
Standby sequence, 3−11
Standby sequence reset method, 5−34
Starting and Stopping Operation, 3−14
Status A, 6−12
Status B, 6−12
Structure of Parameters, 7−2
Summary of alarm operations, 3−11
Switching with Manual operation, 4−2
T
Temperature input, 1−4 , 3−5
Temperature input shift, 3−5
Temperature unit, 3−5
Terminal arrangement, 2−7
The meaning of icons used in this chapter, 5−2
Thermocouple, 7−12
U
Up key, 1−3
Using the E5EK−DRT in Multi−vendor Ap
plications, A−13
V
Vendor−specific object processing time, 6−5
Vendor−specific Objects (0x94), A−17
Voltage input, 1−4 , 7−13
W
Wiring, 2−7
Wiring Terminals, 2−7
Write data assignment 1 to 16, 5−38
Writing parameters, 6−13