Omron E5EK - MANUAL 2 User Manual page 153

Data Timing, 6−13
Data type list, 6−9
Data write processing time, 6−5
Data writing processing time, 6−5
Dead band, 4−2 , 5−13
Decimal point, 5−26
Derivative time, 5−12
Determining the LBA detection time, 4−12
DeviceNet Object (0x03), A−14
Differences from General−purpose Models,
1−6
Dimensions, 2−4 , A−5
Direct/Reverse operation, 3−8 , 5−30
Display range over, 8−4
Down key, 1−3
Draw−out, 2−2
E
E5EK−DRT Internal Processing Times, 6−5
Example of actual calculation, 6−5
Examples of use, 4−10
Executing operation instructions, 6−13
Expansion Mode, 1−6 , 1−7 , 5−31
F
Fixing Screw for Front Panel, 2−2
Fixing settings, 1−8
Flow of Communications Processing, 6−4
Front panel, 1−2
H
HBA latch, 5−39
HBA latch/release, 4−9
Heater burnout, 5−16
Heater Burnout Alarm, A−3
Heater burnout detection, 4−9
Heater current monitor, 5−15
Heating and cooling control, 4−2
How to assign data, 6−8
How to calculate the heater burnout set value,
4−10
How to Use Error Output, 8−5
How to use keys, 1−3
How to Use the Error Display, 8−3
How to Use the Heater Burnout Alarm, 4−9
How to Use the Remote SP , 4−7
Hysteresis, 4−3
Hysteresis (cool), 5−14
Hysteresis (heat), 5−14
I
Identity Object (0x01), A−14
Initial Checks, 8−2
Input and Output, 1−4
Input digital filter, 5−22
Input error, 8−3
Input errors, 8−5
Input shift lower limit, 5−23
Input shift upper limit, 5−23
Input type, 3−4 , 5−25
Installation, 2−4
Integral time, 5−12
L
LBA, 4−11 , 8−5
LBA detection example, 4−11
LBA detection time, 4−11 , 5−20
LBA detection width, 4−11 , 5−35
Level 0 Mode, 1−6 , 1−7 , 5−6
Level 1 Mode, 1−6 , 1−7 , 5−10
Level 2 Mode, 1−6 , 1−7 , 5−17
Limiter operation conditions, 4−5
M
Main parts, 1−2
Manipulated variable at stop, 3−14 , 4−2
Manipulated variable restrictions, 4−4
Manual Mode, 1−6 , 1−8 , 5−5
Manual MV , 5−5
Manual operation, 3−15
Manual reset value, 5−13
Memory error, 8−3
Menu display, 1−7
Message Router Object (0x02), A−14
Mounting, 2−5
MS/NS Indicator, 8−2
MS/NS indicators, 1−3
MV at PV error, 5−20
MV at stop, 5−20
MV change rate limit, 5−21
MV change rate limiter, 4−4
MV limiter, 4−4
MV lower limit, 5−21
MV monitor (cool), 5−9
MV monitor (heat), 5−9
MV upper limit, 5−21
N
Names of parts, 1−2
No.1 display, 1−3
No.2 display, 1−3
Node address, 5−37 , 6−6
O
Object Mounting, A−14
ON/OFF control, 4−3
Operating Condition Restrictions, 4−4
Operating conditions, 4−8 , 4−9
Operation at communication error, 5−38 ,
6−9
Operation at start, 4−6
Operation indicators, 1−3
Operation instructions, 6−11
Option Mode, 1−7 , 5−36
Outline of CompoBus/D, 6−2
INDEX