Table of Contents
Advertisement
Par.N.
24.37
Delivery temperature 2 T+H probe calibration
24.38
Delivery temperature 3 T+H probe calibration
24.39
Delivery temperature 4 T+H probe calibration
24.46
External serial temperature TH probe calibration
24.47
External serial humidity TH probe calibration
24.48
Humidity differential for the update of the reading of external T+H probe
24.49
Temperature differential for the update of the reading of external T+H probe
24.52
Delivery TH serial temperature probe calibration
24.53
Delivery TH serial humidity probe calibration
Emergency function configuration (0:Disabled – 1:Enabled)
25.01
Emergency contact status configuration (0:NO – 1:NC)
25.02
Emergency fan status configuration (0:Disabled – 1:Enabled)
25.03
Indoor fan Emergency status configuration for CW units (0:Disabled –
25.05
1=Low speed – 2:nominal Speed)
25.04
Internal fan speed in Emergency mode
Emergency compressor status configuration (0:Disabled – 1:Enabled)
25.06
Emergency heater status configuration (0:Disabled – 1:Enabled)
25.07
Emergency humidifier status configuration (0:Disabled – 1:Enabled)
25.08
Emergency Free Cooling damper status configuration (0:Disabled –
25.09
1:Enabled)
25.10
Setpoint (T_ROOM-T_EXTERNAL) for Free Cooling damper adjustment in
Emergency
25.11
Free Cooling damper adjustment band in Emergency
26.01
Number of units in LAN
Configuration of standby mode function in LAN (0:Disabled – 1:Enabled)
26.03
26.04
Standby cycle time in LAN
Configuration of number of units on standby in LAN (0:1 unit – 1:2 units)
26.05
Configuration of standby mode limits function in LAN (0:Disabled –
26.06
1:Enabled)
Configuration of average calculation function in LAN (0:Disabled –
26.02
1:Enabled)
26.08
Configuration of maximum delivery temperature value calculation in LAN
(0:Disabled – 1:Enabled)
Enable the H&L Local Temperature Protection function (0:Disabled –
26.11
1:Enabled)
26.12
Hot Spot function On differential
26.13
Cold Spot function On differential
26.14
Time before protection Off when the temperature is between the limits of the
Cold and Hot Spot
26.15
Time before protection On when outside the limit of the Hot or Cold Spot
Enable the Active Fan on Standby function (0:Disabled – 1:Enabled)
26.16
26.17
Internal fan speed with Active Fan on Standby in use
Enable the Active Pressure Load function (0:Disabled – 1:Enabled)
26.18
Version 38
Description
Default
U.M.
Min.
0
°C
-9.9
0
°C
-9.9
0
°C
-9.9
0
°C
-9.9
0
%RH
-9.9
0.5
°C
0.1
0.5
%RH
0.1
0
°C
-9.9
0
%RH
-20
0
-
0
0
-
0
1
-
0
2
-
0
50
%
0
1
-
0
0
-
0
0
-
0
0
-
0
1
°C
0
0.5
°C
0
1
-
1
0
-
0
168
-
0
0
-
0
1
-
0
0
-
0
0
-
0
0
-
0
2
°C
0.5
2
°C
0.5
300
s
10
60
s
10
0
-
0
70
%
P
99.01
0
-
0
Max.
9.9
9.9
9.9
9.9
9.9
2
2
9.9
20
1
1
1
2
99
1
1
1
1
99.9
9.9
15
1
999
14
1
1
1
1
99.9
99.9
600
600
1
100
1
103
Advertisement
Table of Contents
