Siemens RUGGEDCOM ROX II User Manual page 541

RUGGEDCOM ROX II
CLI User Guide
show switch layer3-switching routing-rules-summary
A table or list similar to the following example appears:
ruggedcom# show switch layer3-switching routing-rules-summary
PACKETS
RULE RULE IN
ROUTING
ID TYPE VLAN
ACTION STATUS
---------------------------------------------------------------------------------------------
0 unicast -
forward active
1 unicast -
forward active
2 unicast -
forward active
3 unicast -
forward active
4 unicast -
forward active
5 unicast -
forward active
6 unicast -
forward active
7 unicast -
forward active
8 unicast -
forward active
9 unicast -
forward active
10 unicast -
forward active
11 unicast -
forward active
12 unicast -
forward active
This table or list provides the following information:
Parameter
rule-id
rule-type
in-vlan
out-vlans
proto
source
src-port
destination
Viewing Routing Rules
OUT
VLAN PROTO SOURCE
- 17 192.12.1.120
- 17 192.12.1.69
- 17 192.11.0.160
- 17 192.11.0.92
- 17 192.12.0.92
- 17 192.12.0.254
- 17 192.12.0.223
- 17 192.11.0.85
- 17 192.12.0.95
- 17 192.12.0.180
- 17 192.12.0.67
- 17 192.12.0.161
- 17 192.11.2.190
Description
Synopsis: An integer between 0 and 2999
Defines the order in which rules are matched on each ingress packet. The first matched rule
is applied on the packet.
Synopsis: { multicast, unicast, invalid, hidden }
Identifies the type of the rule: unicast,multicast,invalid.
Identifies the ingress VLAN. To match the rule, the packet's ingress VLAN must match the
number.
Identifies the egress VLAN. The matched multicast packet is sent to the identified VLAN.
The IP Encapsulated Protocol number. Unless zero is specified, the incoming packet's IP
protocol must match this number.
Synopsis: { any } or a string
Identifies the source IP address or subnet. To match the rule, the incoming packet's source
IP address must belong to the subnet.
Synopsis: An integer between 0 and 65535
The port associated with the source flow. A value of 0 means Not Applicable.
Synopsis: { any } or a string
SRC DEST
PORT DESTINATION PORT
1024 192.11.1.120 1024
1024 192.11.1.69 1024
1024 192.12.0.160 1024
1024 192.12.0.92 1024
1024 192.11.0.92 1024
1024 192.11.0.254 1024
1024 192.11.0.223 1024
1024 192.12.0.85 1024
1024 192.11.0.95 1024
1024 192.11.0.180 1024
1024 192.11.0.67 1024
1024 192.11.0.161 1024
1024 192.12.2.190 1024
Setup and Configuration
PER
GATEWAY SECOND
192.11.1.120 11
192.11.1.69 11
192.12.0.160 11
192.12.0.92 11
192.11.0.92 11
192.11.0.254 11
192.11.0.223 11
192.12.0.85 11
192.11.0.95 11
192.11.0.180 12
192.11.0.67 11
192.11.0.161 11
192.12.2.190 11
Chapter 5
STATIC
false
false
false
false
false
false
false
false
false
false
false
false
false
503