Mitsubishi Electric MELSERVO-J4 Series Instruction Manual page 575

■Peripheral device and power wiring
The following are selected based on IEC/EN 61800-5-1, UL 508C, and CSA C22.2 No. 14.
• Local wiring and crimping tool
The following table shows the stranded wire sizes [AWG] and the crimp terminal symbols rated at 75 /60 .
*7
Servo amplifier
MR-J4-03A6/MR-J4W2-0303B6
MR-J4-10_(1)/MR-J4-20_(1)/MR-J4-40_(1)/
MR-J4-60_(4)/MR-J4-70_/MR-J4-100_(4)/
MR-J4-200_(4) (T)/MR-J4-350_4
MR-J4-200_ (S)
MR-J4-350_
*1
MR-J4-500_
*1
MR-J4-700_
*1
MR-J4-11K_
*1
MR-J4-15K_
*1
MR-J4-22K_
*1
MR-J4-500_4
*1
MR-J4-700_4
*1
MR-J4-11K_4
*1
MR-J4-15K_4
*1
MR-J4-22K_4
MR-J4W_-_B
*1 To connect these models to a terminal block, be sure to use the screws that come with the terminal block.
*2 Alphabets in the table indicate crimping tools. Refer to the following table for the crimp terminals and applicable tools.
*3 Select wire sizes depending on the rated output of the servo motors. The values in the table are sizes based on rated output of the servo
amplifiers.
*4 Use the crimp terminal c for the PE terminal of the servo amplifier.
*5 This value is of 24/0/PM/
*6 This value is of U/V/W/E for MR-J4-03A6 and MR-J4W2-0303B6.
*7 "(S)" means 1-phase 200 V AC power input and "(T)" means 3-phase 200 V AC power input in the table.
Symbol Servo amplifier-side crimp terminals
Crimp terminal
a FVD5.5-4
*1
b 8-4NS
c FVD2-4
d FVD14-6
e FVD5.5-6
f FVD22-6
g FVD38-6
h R60-8
i FVD5.5-8
j CB70-S8
k FVD2-6
l FVD8-6
m FVD14-8
n FVD22-8
*1 Coat the crimping part with an insulation tube.
*2 Some crimp terminals may not be mounted depending on the size. Make sure to use the recommended ones or equivalent ones.
75 /60  stranded wire [AWG]
L1/L2/L3
*5
19/-
14/14
12/12
10: a/10: a
8: b/8: b
6: d/4: f
4: f/3: f
1: h/-: -
14: c/14: c
12: a/12: a
10: e/10: e
8: l/8: l
6: m/4: m
*4
14/14
for MR-J4-03A6 and MR-J4W2-0303B6.
*2
Applicable tool
YNT-1210S
YHT-8S
YNT-1614
YF-1
YNT-1210S
YF-1
YF-1
YF-1
YNT-1210S
YF-1
YNT-1614
YF-1
YF-1
YF-1
*2
L11/L21 P+/C
 
14/14 14/14
14: c/14: c 14: c/14: c
12: a/12: a
12: e/12: e
10: e/10: e
10: i/10: i
14: c/14: c
14: k/14: k
12: e/12: e
12: i/12: i
14/14 14/14
Manufacturer
JST
(J.S.T. Mfg. Co., Ltd.)
Appendix 4 Compliance with global standards
*3
U/V/W/
*6
19/-
14/14
12/12
10: b/10: b
8: b/8: b
4: f/4: f
3: g/2: g
1: j/-: -
12: a/10: a
10: a/10: a
8: l/8: l
6: d/4: d
6: n/4: n
14/14
A
APPX
573