System Settings; Network Setup; Prefix Length Settings; Appletalk Setup - Kyocera TASKalfa 250ci Service Manual

(13) System Settings

Restarting the System
1. Press [Execute] of Restart.
2. When the confirmation screen appears, press
[Yes]. The system is restarted.

Network Setup

LAN Interface Setup
1. Press [Next] of Network and then [Change] of LAN
Interface.
2. Select [Auto], [10BASE-T Half], [10BASE-T Full],
[100BASE-TX Half] or [100BASE-TX Full] as the
LAN interface.
3. Press [OK].
4. After changing the setting, restart the system or
turn the machine OFF and then ON again.
TCP/IP (IPv4) Setup
1. Press [Next] of Network and then [Next] of TCP/IP
Setting.
2. Press [Change] of TCP/IP.
3. Press [On] and then press [OK].
4. Press [Change] of IPv4.
5. Press [DHCP].
6. Press [Off] of DHCP and then press [OK].
7. Press [Bonjour].
8. Press [Off] of Bonjour and then press [OK].
9. Press [IP Address] and enter the address using the
numeric keys.
10. Press [Subnet Mask] and enter the address using
the numeric keys.
11. Press [Default Gateway] and enter the address
using the numeric keys.
12. Check if all the address entries are correct and
press [OK].
13. After changing the setting, restart the system or
turn the machine OFF and then ON again.
TCP/IP (IPv6) Setup
1. Press [Next] of Network and then [Next] of TCP/IP
Setting.
2. Press [Change] of TCP/IP.
3. Press [On] and then press [OK].
4. Press [Change] of IPv6.
5. Press [On].
6. Press [OK].
7. After changing the setting, restart the system or
turn the machine OFF and then ON again.
DHCP (IPv6) Settings
1. Press [Next] of Network and then [Next] of TCP/IP
Setting.
2. Press [Change] of TCP/IP.
3. Press [On] and then press [OK].
4. Press [Change] of IPv6.
5. Press [On].
6. Press [DHCP].
7. Press [On] or [Off] of DHCP.
8. Press [OK].
9. After changing the setting, restart the system or
turn the machine OFF and then ON again.
RA (Stateless) Settings
1. Press [Next] of Network and then [Next] of TCP/IP
Setting.
2. Press [Change] of TCP/IP.
3. Press [On] and then press [OK].
4. Press [Change] of IPv6.
5. Press [On].
6. Press [RA(Stateless)] .
7. Press [On] or [Off] of RA (Stateless).
8. Press [OK].
9. After changing the setting, restart the system or
turn the machine OFF and then ON again.

Prefix Length Settings

1. Press [Next] of Network and then [Next] of TCP/IP
Setting.
2. Press [Change] of TCP/IP.
3. Press [On] and then press [OK].
4. Press [Change] of IPv6.
5. Press [On].
6. Press [Prefix Length] and then press [+] or [-] to
enter the prefix length. You can enter a prefix length
between 0 and 128.
7. Press [OK].
8. After changing the setting, restart the system or
turn the machine OFF and then ON again.
NetWare Setup
1. Press [Next] of Network and then [Change] of Net-
Ware.
2. Press [On].
3. Press the key for the frame type you want to use.
4. Press [OK].
5. After changing the setting, restart the system or
turn the machine OFF and then ON again.

AppleTalk Setup

1. Press [Next] of Network and then [Change] of
AppleTalk.
2. Press [On] or [Off].
3. Press [OK].
4. After changing the setting, restart the system or
turn the machine OFF and then ON again.
2JZ/2JX/2JV/2H7-1
1-3-153