Extron electronics DMP 128 User Manual page 150

Command and Response Table for DSP SIS Commands (continued)
Command ASCII command
(host to device)
Audio group master commands
NOTES: • See Group Masters,on page 83 for more information about audio group masters.
• A group must have assigned members for these commands to have an effect.
X6^
• For , a positive (+) value is assumed unless a negative (-) value is specified.
X6^
• If entering a value outside the valid range for the group or outside the soft limits, the DMP 128 responds with an
"invalid parameter" (E13) error.
X6^ X6& X6*
• , , and
Set a group fader
E
control
E
Example:
Raise a group E
fader control
Example: E
Lower a group
E
fader control
View the group E
fader control level
Mute a group E
mute control
Clear (unmute) a
E
group mute control
View a group mute
E
control
Set soft limits E
Example: E
View soft limits E
View group type E
View group E
members
X6)
NOTES: = Gain and trim control
X6%
= Group master group number
X6^
= Group fader level
X6&
= Group fader increase and decrease
X6*
= Group fader soft limit
X6(
= Group type
Response
(device to host)
values can be sent without leading zeroes; responses are always 5 digits.
X6% X6^ }
D * GRPM GrpmD
}
d2*-293GRPM GrpmD02*-00293
X6% X6& }
D * +GRPM GrpmD
}
d2*30+GRPM GrpmD02*-00263
X6% X6& }
D * -GRPM GrpmD
X6% }
D GRPM GrpmD
X6% }
D *1GRPM GrpmD
X6% }
D *0GRPM GrpmD
X6% }
D GRPM GrpmD
X6% X6* X6* }
upper lower
L GRPM
* *
GrpmL
} Grpm
L2 * +60 * -60GRPM
X6% }
L GRPM GrpmL
X6% }
P GRPM GrpmP
X6% }
O GRPM GrpmO
...
table 1
See
01 to 32
dB value, in 0.1 dB increments, using negative numbers and eliminating
decimal places using a 10x multiplier. -100.0 dB to +80.0 dB is
represented by -1000 to 800.
The valid range depends on the type of gain or trim block assigned
to the group number (
dB value, in 0.1 dB increments, to raise or lower a group fader.
dB value, in 0.1 dB increments. The valid range must be within the
range for the gain block grouped in
6 = gain
12 = mute
X6% X6^]
*
]
X6% X6^]
*
]
X6% X6^]
*
X6% X6^]
*
X6% ]
*+00001
X6% ]
*+00000
X6% X6$]
*
X6% X6* X6*]
* *
* *- ]
L02 00060 00060
+
X6% X6* X6*
* * ]
X6% X6(]
*
X6% X6) X6)
* * *
1 2
X6) ]
*
16
on page 148.
X6%
).
X6%
.
DMP 128 • SIS Programming and Control
Additional description
X6^
Set a group fader to a value of
Set the group 2 fader control to
-29.3 dB.
X6%
Increase the level of the group
X6&
fader by dB.
Raise the group 2 fader 3 dB (from
-29.3 dB to -26.3 dB, starting from
the level set in the "Set a group fader
control" example, above.
X6%
Decrease the level of the group
X6&
fader by dB.
In verbose modes 1 and 2, the
X6^]
response is simplified to .
X6%
Mute all blocks in group .
X6%
Umute all blocks in group .
X6$
For group masters, is always
expressed as a positive or negative
5-digit value.
X6*
Set the groups soft limits to and
X6*
.
Set the upper soft limit for the group
2 fader to +6.0 dB and the lower limit
to -6.0 dB.
In verbose modes 0 and 1, the
X6* X6*]
response is simplified to *
X6(
Show the group type ( ) for group
X6%
. In verbose modes 0 and 1, the
X6(]
response is simplified to .
X6)
is the control address.
In verbose modes 0 and 1,
the response is simplified to
X6) X6) X6) ]
* *...* .
1 2 16
.
.
144