Extron electronics DMP 128 Plus Setup Manual

DMP 128 Plus • Setup Guide
This guide provides basic instructions for an experienced technician to install the DMP 128 Plus ProDSP
Processor. For additional information and specifications, see the DMP 128 Plus product page at www.extron.com.
ACTIVITY
EXP LAN
CONFIG
Disconnect Power and Mount the DMP 128 Plus
A B C D E
Disconnect power to the DMP 128 Plus and turn off all devices that will be connected to it. The DMP 128 Plus is housed in a full
rack width, 8.5 inch deep, 1 U high metal enclosure that can sit on a table with the provided rubber feet or can be rack mounted.
Select a suitable mounting location, then choose an appropriate mounting option. Mounting information can be found in the
DMP 128 Plus User Guide on www.extron.com.
Make all external device connections before applying power.
100-240V 0.7A MAX
1
2 3
IN G O1 O2 IN G O1 O2 IN G O1 O2
1 2 3
50 - 60 Hz
A B
Figure 1. DMP 128 Plus Rear Panel
Connections
AC Power — IEC power connector, 100 — 240 VAC, 50 — 60 Hz.
A
Digital I/O Connectors — Connect up to eight 4-pole 3.5 mm captive screw connectors. These connectors provide
B
configurable digital input and output ports designed to connect to microphones with logic circuitry for mic mute and tally
back functionality. Each port provides a common ground.
Mic/Line Input Connectors — Connect up to eight balanced or unbalanced microphone or mono line level signals using
C
3-pole 3.5 mm captive screw connectors to inputs 1 through 8 (see Audio Input Wiring below). These ports provide Phantom
Power and AEC.
Connect up to four balanced or unbalanced mono microphone or line level devices, or two stereo devices, using 6-pole
3.5 mm captive screw connectors on inputs 9 through 12 (see Audio Input Wiring below).
3 " (5 mm) MAX. (typ)
16
Tip
Ring
Sleeve
Balanced Input
Audio INPUT Wiring
NOTES:
• Balanced or unbalanced stereo devices can be connected to the
6-pole connections.
• When using the 5-pole CSR adapter, connect it so the far left plug
is inserted into the far left jack of the 6-pole input connector
(see example to the right).
INPUTS
1 2 3 4 5 6 7 8 9
CLIP
USB
SIGNAL
F
9 10
4 5 6 7 8
IN G O1 O2 IN G O1 O2 IN G O1 O2 IN G O1 O2 IN G O1 O2
11 12
4 5 6 7 8
C
Tip
Sleeve
Jumper
Unbalanced Input
OUTPUTS
10 11 12 1 2 3 4 5 6 7 8
CLIP
SIGNAL
G
1 2 3 4
DMP 128 Plus C
5 6 7 8
+V +S -S G
D E F
Tip
Ring
Sleeve
Tip
1 0
0 - 2
4 0
Ring
Sleeve
Balanced Input
5 0
Digital Matrix
™
DMP 128 Plus
DIGITAL MATRIX PROCESSOR
USB AUDIO
RS-232 RESET
Tx Rx G LAN
G H I J
Tip
Sleeve
Jumper
Tip
V ~
- - A Sleeve
M A
X
Jumper
Unbalanced Input
6-pole Audio INPUT Wiring
1
M I
C
1
/ 6 0 + 4
H z 2 8 V
2
3
4
5
3
6
5
7
8
4
6
7
8
5-pole CSR
DO NOT
Connect Here
9
1 0
D M
P 1
2 8
1 1
1 2
1
5
1