Fujitsu PRIMEQUEST 2000 Series Tool Reference page 336

MMB CLI (Command Line Interface) Operations
sysconf input_voltage | reserved_sb | exit_code]
show partition configuration [ all | free | <partition#> {[, | -] <partition#>}]
show partition [home | name | dynamic_reconfiguration | memory_operation_mode |
memory_mirror_ras_mode | pci_address_mode |
pci_express_mode | lan_device_mode] <partition#>
netck [arptbl | ifconfig | stat | traceroute <ip> | arping <ip>]
console <partition#> {<timeout>} {quiet}
nmi {partition} [ <partition#> [, | -] <partition#>] {quiet}
reset {partition} [ <partition#> [, | -] <partition#>] {quiet}
sadump {partition} [ <partition#> [, | -] <partition#>] {quiet}
exit
passwd {USER}
ping {-c <count>} [<ip address> | <server name>]
who
help
#
[When the PRIMEQUEST 2800E model]

Example 1: For the Administrator privilege
#help
factory_default {-f}
add partition <partition#> [ SB <SB#> | IOU <IOU#> ] {quiet}
clear access_control
power off {partition} [ all | <partition#>[,| -]<partition#>] {force}
power on {partition} [ all | <partition#>[,|-]<partition#>]
remove partition <partition#> [ SB <SB#> | IOU <IOU#>] {quiet}
set active_mmb {0 | 1} {quiet}
set date MMDDhhmm{{CC}YY}{,ss}
set timezone <timezone>
set gateway <ip address>
set gateway_ipv6 [auto | <ip address>]
set [ http | https | ssh | telnet ] [ enable | disable ]
set [ http_port | https_port | ssh_port | telnet_port ] <port>
set partition home <partition#> SB <SB#>
set partition name <partition#> <partition name>
set partition dynamic_reconfiguration <partition#> [disable | enable] {quiet}
set partition memory_operation_mode <partition#> [performance | normal | partial_mirror | spare]
{quiet}
set partition memory_mirror_ras_mode <partition#> [mirror_keep | capacity_keep] {quiet}
set partition pci_address_mode <partition#> [bus | segment] {quiet}
set partition pci_express_mode <partition#> [ flexible | fixed ]
set partition lan_device_mode <partition#> <IOU#> [wol_enable | wol_disable | device_disable] {quiet}
set ip <ip address> <netmask>
set ipv6 [auto | <ip address>/<prefix>]
set hostname <hostname>.<domain name>
set maintenance_ip <ip address> <netmask> <gateway address> <smtp address>
set sysconf power_feed_mode [single | dual] {quiet}
set sysconf power_restoration_policy [on | off | restore | sync] {quiet}
set sysconf power_on_delay <time> {quiet}
set sysconf altitude <altitude>
set sysconf psu_redundant_mode [redundant | non_redundant] {quiet}
set mmbcontrol reset [0 | 1] {quiet}
set mmbcontrol switch_over {quiet}
set reserved_sb <SB#> <partition#> {quiet}
set snmp sys_location <location> {quiet}
set snmp sys_contact <concat> {quiet}
set snmp community <community> <ip or mask> [1 | 2] [ro | rw] {quiet}
set snmp trap <community> <ip> [1 | 2] {quiet}
set snmp test_trap {quiet} show [access_control | active_mmb | date | timezone | gateway | gateway
ipv6 |
http | http_port | https | https_port | ssh | ssh_port | telnet |
telnet_port | ip | ipv6 | hostname | network | maintenance_ip | ntpq |
sysconf power_feed_mode | sysconf power_restoration_policy |