Gp 1.1 General Specifications - Xerox N2125N - DocuPrint B/W Laser Printer Service Manual

GP 1.1 General Specifications

Table 1 General Specifications
Category Specification
Printing method Electro-photographic system (roller charging, single com-
ponent magnetic toner development)
Exposure method Semiconductor Laser Beam Scanning
Laser specifications Class 1 Laser Product
Class 3B Laser, rated at 5mW output @ 780nm
Resolution 600/1200 dots per inch (dpi), switchable at full engine
speed.
Fuser method Heat and pressure
Warm-up time From a cold start (22°C / 71.6°F ambient temperature) to
READY TO PRINT within 65 seconds.
Power supply 100/120VAC (90-140VAC) 50/60Hz (47Hz -63Hz)
220/240VAC (198-264VAC) 50/60Hz (47Hz -63Hz)
Power consumption 100/120VAC printer: Maximum consumption: 800W Run-
ning, 45 W Sleep, Maximum current: 8A (100VAC)/6.66A
(120VAC).
240VAC printer: Maximum consumption: 800W Running,
45W Sleep. Maximum current: 3.33A (240VAC).
Note: No electrical current is supplied to the Fuser assem-
bly in Sleep Mode.
Fuser control temperature 100/120VAC printer: T.B.D°C / °F
220/240VAC printer: T.B.D°C / °F
Size and weight (not including the Width 422mm X Depth 439mm X Height 413mm (16.5
Print Cartridge, System Controller inches x17.25 inches x 16.25 inches)
PWB or any options) Weight = 26Kg (57lbs)
Space requirements Overhead: Minimum T.B.D. mm
Front: Minimum 240mm (9.5 inches)
Back: Minimum 300mm (11.8 inches)
Sides: Minimum T.B.Dmm
Maximum paper size Legal 14" (8.5"X14" = 355.6mm X 215.9mm)
Maximum printable area Edge to edge printing capability. Within the 4mm border (4
sides) the printer will print any data 6 point Arial or larger.
Maximum paper load 550 sheets of RX 80 A4 paper, or Xerox 20lb Letter size
paper.
Operating environment 5 - 35 C / 41° - 95°F @ 15% to 85% RH (operating)
0 - 3100 meter (10171.1 ft.) above sea level
Horizontal bias within 5 of level
Storage environment with a Normal condition:12 months maximum at 0-35°C/32-95°F
packed Print Cartridge @ 15-80%RH with no condensation present
Severe condition: 1 month maximum at -20 to 0°C / -4 to
32°F or 35 to 40°C / 95 to104°F
@ 5-15 or 80-95%RH with no condensation present
Initial Issue
DocuPrint N2125
Category
Storage environment without a
packed Print Cartridge
Acoustic Noise
Dust generated
Print Cartridge life (See GP 1.7)
Toner Sensor
02/2000
6-5
manuals4you.com manuals4you.com
Table 1 General Specifications
Specification
Normal condition: 12 months maximum at -20 to -50°C / -4
to -58°F
@ 5-85% RH with no condensation present
Severe condition: 48 hours maximum at 50-60°C / 122 -
140 °F
@ 85-95% RH with no condensation present
Standby mode: 35.0dB(A)
Sleep mode: Background noise only
Printing mode: 49.5dB(A) or 53.0dB(A)
Base Engine: Duplex Assembly, Tray 2, Tray 3, Envelope
Feeder, and OCT.
The paper is 20lb Letter SEF, at 600 dpi.
No more than 0.1mg/m3 of dust
*10,000/15,000 prints on A4/Letter paper, with 5% print
coverage
(*10,000 or 15,000 prints dependent on Print Cartridge
used)
After Toner Sensor detects a low level of toner in the CRU,
the printer makes ten additional prints before generating
an J5 error message.
General Procedures / Information
GP 1.1