1
2
3
4
Table of Contents
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
Advertisement
Table 4-1
Heading
34
Chapter 4 System management
Computer Setup (F10) Utility menu descriptions (continued)
Option
Description
POST Delay (None (default), 5, 10, 15, 20 seconds)—Delays start of the POST
●
process. You might need a delay to:
◦
◦
Remote Wakeup Boot Source (Local Hard Drive/Remote Server). Sets the boot device
●
for the workstation when it is started using Remote Wakeup (takes precedence over the
Boot Order menu setting) .
System Recovery Boot Support (Enabled/Disabled). Enabling this feature displays an
●
additional prompt, F11=Recovery, during POST on systems with HP Backup and
Recovery software installed and configured with a recovery partition on the boot hard
drive. Pressing F11 causes the system to boot to the recovery partition and launch HP
Backup and Recovery. You can hide the F11=Recovery prompt by using the F11
prompt option described above.
Bypass F1 Prompt on Confirmation Changes (Enabled/Disabled)—Prevents display of a
●
confirmation prompt when you make changes to the system.
BIOS Power-On
Lets you disable or specify a weekday and time for BIOS power-on.
Onboard Devices
Lets you disable or set resources (IRQ, DMA, I/O Rate) for onboard system devices such as
the serial port and parallel ports. Operating system parameters generally override Onboard
Devices settings.
Bus options
Enable/disable these options:
PCI SERR# Generation (Enabled/Disabled)—Controls PCI SERR# generation for ill-
●
behaved PCI add-in cards (that can generate SERR# spuriously)
PCI VGA Palette Snooping (Disabled/Enabled)—Controls PCI VGA Palette Snooping
●
for compatibility purposes
PCI Latency Timer (32/64/128/160/192/224/248). 128 PCI Clocks is the default.
●
NOTE:
If you turn off power to the computer using a power strip, you cannot use
the suspend/sleep feature or the Remote Management features.
Allow time for some hard disk drives to spin up before POST is finished
Give yourself more time to select F10 to enter the Computer Setup (F10) Utility.
ENWW
Advertisement
Table of Contents
Troubleshooting
Related Manuals for HP Z210
-
Desktop HP Z210 Support Manual
Hardware support matrix for current hp linux workstations (22 pages)
-
Desktop HP 175753-002 - iPAQ - 64 MB RAM Support Telephone Numbers
Support telephone numbers (19 pages)
-
Computer Hardware HP Z210 Installation Manual
Hp workstations - cru dataport dx115 kit installation (19 pages)
-
Desktop HP Z210 Series Rack Mounting Instructions
Hp z200, z400 and xw4000 workstations - rack mount tray installation (10 pages)
-
Desktop HP Z200 - Small Form Factor Workstation Installation Manual
Broadcom netxtreme gigabit ethernet plus network interface card installation (6 pages)
-
Desktop HP Z210 Quick Reference Card
Hp workstation quick reference card (2 pages)
-
Desktop HP Z210 Declaration Of Conformity
Computer workstation (1 page)
-
Desktop HP Z210 Declaration Of Conformity
Cmt workstation (1 page)
-
Desktop HP Workstation Z210 CMT Specifications
Hp workstation z210 cmt: specifications (50 pages)
-
Desktop HP Z220 Installation Manual
Hp workstations - cru dataport dx115 kit installation (22 pages)
-
Desktop HP Z220 Specification
Hp z220 cmt workstation (55 pages)
-
Desktop HP Z200 Maintenance And Service Manual
Small form factor workstation (210 pages)
Comments to this Manuals
Latest comments: