Download
Share
Print this page
HP Z210 Installation Manual
  1. Manuals
  2. Brands
  3. HP Manuals
  4. Computer Hardware
  5. Z210 Series
  6. Installation manual

HP Z210 Installation Manual

Hp workstations - cru dataport dx115 kit installation
Hide thumbs Also See for Z210:

Advertisement

Quick Links

Download this manual See also: Maintenance and Service Manual, User Manual

CRU Dataport DX115 kit installation

Introduction
This document describes how to install the CRU Dataport DX115® removable media kit in an HP
computer. The DX115 kit lets you install removable media in your computer.

Kit contents

●
Warranty information
●
DX115 unit (case, drive carrier, and lock key)
●
Installation document
●
SATA or SAS cable
●
Five M3 screws
●
Five 6-32 screw
●
Tape label

Before you begin

To view QuickSpecs and determine the compatibility of this product with your HP computer, see
http://www.hp.com/go/productbulletin.
ENWW
© 2006–2010 Hewlett-Packard Development Company, L.P. Microsoft, Windows,
and Windows Vista are U.S. registered trademarks of Microsoft Corporation.
Printed in the U.S.
Introduction
1

Advertisement

loading

Related Manuals for HP Z210

Summary of Contents for HP Z210

  • Page 1: Cru Dataport Dx115 Kit Installation

    Before you begin To view QuickSpecs and determine the compatibility of this product with your HP computer, see http://www.hp.com/go/productbulletin. © 2006–2010 Hewlett-Packard Development Company, L.P. Microsoft, Windows, and Windows Vista are U.S. registered trademarks of Microsoft Corporation. Printed in the U.S.

  • Page 2: Warnings And Cautions

    Warnings and cautions WARNING! Any surface or area of the equipment marked with this symbol indicates the presence of a hot surface or hot component. If this surface is contacted, the potential for injury exists. To reduce the risk of injury from a hot component, enable the surface to cool before touching. WARNING! Any surface or area of the equipment marked with this symbol indicates the presence of an electrical shock hazard.

  • Page 3: Accessing The Internal Components Of The Computer

    Accessing the internal components of the computer If you need help preparing the computer for this installation, consult the removal and replacement procedures in the service guide for your computer at http://www.hp.com/support/ manuals. Power down the computer, and then disconnect the power cord. Power down all external devices, and then disconnect them from the computer.
  • Page 4 Figure 1 Removing the SAS to SATA adapter CRU Dataport DX115 kit installation ENWW...
  • Page 5 HP Z200 SFF computer To install a DX115 case in a Z200 SFF computer: Remove the front bezel: If necessary, remove the bezel security screw, located beside the middle bezel release tab. Figure 2 Removing the bezel security screw Lift the release tabs (1), and then rotate the front bezel off the chassis (2). Figure 3 Removing the front bezel Step 2—Installing the DX115 case into the optical drive bay...
  • Page 6 If necessary, remove the optical disk drive blank from the bezel: On the inside of the bezel, push the two retaining tabs toward the outer edge of the bezel Slide the bezel blank back away from the bezel and to the left to remove it (2). Figure 4 Removing the bezel blank If an existing optical disk drive is present, remove it:...
  • Page 7 Disconnect the power cable (1) and data cable (2) from the rear of the optical drive. Figure 6 Removing the cables Rotate the drive cage back down to its normal position. CAUTION: Check clearances on the cables when you rotate the drive cage. The cage may pinch the cables and damage them if they are not routed correctly.
  • Page 8 Remove and discard the counter-sunk shipping screw at the side of the DX115 case. Figure 8 Removing the shipping screw Install four (supplied) M3 x 5mm screws (black) in the lower four mounting holes of the DX115 case. Figure 9 Installing the guide screws Position the guide screws on the drive into the J-slots in the drive bay.
  • Page 9 Rotate the drive cage to its upright position. Figure 11 Rotating the drive cage up If the cables are not already routed and attached to the system board: Connect the SATA data cable to the system board connector labeled SATA1. Route the data cable through the cable guides to keep the data cable from being pinched by the drive cage when raising or lowering it.
  • Page 10 Connect the power cable (1) and data cable (2) to the rear of the DX115 case. Figure 13 Connecting the power and data cables Carefully rotate the drive cage back down to its normal position. CAUTION: Check clearances on the cables when you rotate the drive cage. The cage may pinch the cables and damage them if they are not routed correctly.
  • Page 11 Remove and discard the counter-sunk shipping screw at the side of the DX115 case. Figure 15 Removing the shipping screw Install four (supplied) M3 x 5mm screws (black) in the lower four mounting holes. Figure 16 Installing the mounting screws Lift the green release lever for the optical bay and slide the DX115 unit into the bay until it is stopped by the release latch as shown in the figure below.
  • Page 12 Install one (supplied) M3 x 5mm screw (black) for each DX115 unit for shipping support as shown. CAUTION: Failure to install the shipping screw might result in damage to the removable hard drive system. Figure 18 Installing the shipping support screw HP xw6200, xw6400, and xw6600 computers Remove the front bezel from the computer.
  • Page 13 Install one (supplied) 6-32 x 1/4 in. screw (silver) for each DX115 unit for shipping support. CAUTION: Failure to install the shipping screw might result in damage to the removable hard drive system. Figure 21 Installing the shipping support screw HP Z600 and Z800 computers For HP Z800 computers: ●...
  • Page 14 Install one (supplied) M3 x 5mm screw (black) for each DX115 unit for shipping support. CAUTION: Failure to install the shipping screw might result in damage to the removable hard drive system. Figure 24 Installing the shipping support screw CRU Dataport DX115 kit installation ENWW...
  • Page 15 HP xw8000 and xw9000 computers Remove the front bezel from the computer. See Figure 14 Removing the front bezel on page Remove and discard the counter-sunk shipping screw at the side of the DX115 case. Figure 25 Removing the shipping screw Lift and hold the drive release latch at the touch point (1) while sliding the DX115 case into the bay (2).
  • Page 16 Step 3—Installing a hard disk in the DX115 carrier Some product options may require you to install a hard drive in the DX115 carrier. For additional information, see: ● The CRU Dataport DX115 User’s Guide for SATA or SAS removable drive enclosures ●...
  • Page 17 Slide the drive all the way to the rear end of the carrier so that the power and data connectors mate with the carrier adapter. Figure 30 Installing the drive Replace the cover by aligning the tab on the rear of the cover with the slot on the rear of the carrier (1) and then rotating the front of the cover onto the carrier (2).
  • Page 18 Step 4—Completing the computer assembly CAUTION: Insert or remove the carrier (with a disk drive) only when the workstation is shut down. Other procedures may result in system hangs, data loss, or even drive damage. The component supplier’s user guide describes a procedure for inserting or removing the carrier (with drive) while the workstation is booted and then powering the drive via the power switch on the enclosure.
  • Page 19 Connect the opposite end of the data cable to the appropriate connector on the system board or controller card. ● Connect SATA drives to SATA ports, and SAS drives to SAS ports, starting with the lowest- numbered available port. ● For HP Z400 and Z600 computers, the blind-mate cables for the internal hard drive bays may require adjustment at the system board, based on the computer drive configuration.

This manual is also suitable for:

Dx115