Page of 6

HP Z200 - Small Form Factor Workstation Installation Manual

Broadcom netxtreme gigabit ethernet plus network interface card installation.
Hide thumbs
   

Advertisement

Broadcom NetXtreme Gigabit Ethernet Plus
Network Interface Card installation
Introduction
This document describes how to install a Broadcom NetXtreme Gigabit Ethernet Plus Network Interface
Card (NIC) into a PCI Express (PCIe) slot on your computer.
Broadcom NetXtreme Gigabit Ethernet Plus NIC
USB cable
Low-profile bracket
Broadcom NetXtreme driver and application CD
Warranty information
Installation instructions
Your responsibilities
You are responsible for determining whether the product is appropriate for your use and will interface
with other equipment without malfunction or damage. You are also responsible for backing up data
before installing any product and for regularly backing up data after installing the product. HP is not
liable for any damage to equipment or data loss resulting from the use of any product. To determine the
compatibility of this product with your computer or workstation, view QuickSpecs at
go/productbulletin.
The Broadcom NetXtreme Gigabit Ethernet Plus NIC is enabled with Desktop and mobile Architecture
for System Hardware (DASH), a new remote IT management tool for desktop and mobile computers.
In some computers, the functionality of the DASH feature might be mutually exclusive with some internal
USB accessories, like the HP Media Reader.
ENWW
© 2009, 2010 Hewlett-Packard Development Company, L.P. Printed in the U.S.
http://www.hp.com/
Introduction
1

Advertisement

   Related Manuals for HP Z200 - Small Form Factor Workstation

   Summary of Contents for HP Z200 - Small Form Factor Workstation

  • Page 1: Kit Contents

    System Hardware (DASH), a new remote IT management tool for desktop and mobile computers. In some computers, the functionality of the DASH feature might be mutually exclusive with some internal USB accessories, like the HP Media Reader. © 2009, 2010 Hewlett-Packard Development Company, L.P. Printed in the U.S. ENWW Introduction...

  • Page 2: Warnings And Cautions

    Warnings and cautions WARNING! Any surface or area of the equipment marked with this symbol indicates the presence of a hot surface or hot component. If this surface is contacted, the potential for injury exists. To reduce the risk of injury from a hot component, enable the surface to cool before touching. WARNING! Any surface or area of the equipment marked with this symbol indicates the presence of an electrical shock hazard.

  • Page 3: Accessing The Internal Components Of The Computer, Removing Components

    Step 1—Preparing for component installation NOTE: Computer models vary. All illustrations are examples only. Download and install updates Check for available system BIOS updates specified for your HP computer model and operating system at http://www.hp.com/support. Install the system BIOS updates, if available. Accessing the internal components of the computer If you need help preparing the computer for this installation, consult the removal and replacement procedures in the service guide for your computer at http://www.hp.com/support/manuals.

  • Page 4

    Step 2—Installing the PCIe NIC hardware If your computer requires a low-profile card, replace the full-height bracket on the card with the supplied low-profile bracket. To install the NIC in the selected PCIe slot: Verify the keyed components of the card align with the socket (1), and then press the card securely into the socket.

  • Page 5

    Step 3—Reassembling the computer Reinstall the card support, if applicable. Reinstall the side access panel. Reconnect power to the computer and all external devices. Restore power to the computer and all external devices. Step 4—Installing NIC software For instructions on installing NIC software, see the driver CD supplied with this installation kit. NOTE: At the time of component installation, look for device software, firmware, and driver updates, designated for your computer model and operating system.

  • Page 6

    Japanese 日本語 This document is available in Japanese. See http://www.hp.com/support/manuals, then select your product and select Japanese from the drop down Manual Language menu. このドキュメントは日本語版が用意されています。http://www.hp.com/support/manuals にアクセス し、ご使用のワークステーション製品を選択し、Manual Language ドロップダウン メニューから Japanese を選択してください。 Broadcom NetXtreme Gigabit Ethernet Plus Network Interface Card installation ENWW...

This manual also for:

Z210, Z400 - workstation

Comments to this Manuals

Symbols: 0
Latest comments: